nr |
titel |
auteur |
tijdschrift |
jaar |
jaarg. |
afl. |
pagina('s) |
type |
1 |
A hybrid approach to multi-criteria optimization based on user’s preference rating
|
Cheema, Manjot S |
|
2013 |
227 |
11 |
p. 1733-1742 |
artikel |
2 |
An industrially feasible approach to process optimisation of abrasive flow machining and its implementation perspectives
|
Howard, Mitchell |
|
2013 |
227 |
11 |
p. 1748-1752 |
artikel |
3 |
Assessment of cutting forces in high-speed milling of Inconel 718 considering the dynamic effects
|
Li, Huaizhong |
|
2013 |
227 |
11 |
p. 1581-1595 |
artikel |
4 |
Defects of wave patterns from tungsten carbide/stainless steel brazed micro-end-milling for printed circuit board machining
|
Kim, Jin-Woong |
|
2013 |
227 |
11 |
p. 1743-1747 |
artikel |
5 |
Directional morphological approaches from image processing applied to automatic tool selection in computer numerical control milling machine
|
Mejia-Ugalde, Mario |
|
2013 |
227 |
11 |
p. 1607-1619 |
artikel |
6 |
Finish machining of mirror-like diamond surfaces using a composite electroplating in-process sharpening method
|
Chen, Tai-Jia |
|
2013 |
227 |
11 |
p. 1596-1606 |
artikel |
7 |
Framework for evaluation of the relative contribution of the process on porosity–cutting force dependence in micromilling of titanium foams
|
Abolghasemi Fakhri, Mohammadmehdi |
|
2013 |
227 |
11 |
p. 1635-1650 |
artikel |
8 |
Hybrid-type spatial mask–panel alignment system for manufacturing flat panel displays
|
Kwon, SangJoo |
|
2013 |
227 |
11 |
p. 1724-1732 |
artikel |
9 |
Improvement of a deburring tool for intersecting holes with reduced irregular cutting of burr edge
|
Cho, Chang-Hee |
|
2013 |
227 |
11 |
p. 1693-1703 |
artikel |
10 |
Investigation of the effect of different cutting parameters on chip formation of low-lead brass with experiments and simulations
|
Laakso, Sampsa VA |
|
2013 |
227 |
11 |
p. 1620-1634 |
artikel |
11 |
Laser–material interaction and grooving performance in ultrafast laser ablation of crystalline germanium under ambient conditions
|
Manickam, Sivakumar |
|
2013 |
227 |
11 |
p. 1714-1723 |
artikel |
12 |
Micro electrochemical sinking and milling method for generation of micro features
|
Ghoshal, B |
|
2013 |
227 |
11 |
p. 1651-1663 |
artikel |
13 |
Modeling of silicon ingot slicing process by wire–electrical discharge machining
|
Dongre, Ganesh G |
|
2013 |
227 |
11 |
p. 1664-1678 |
artikel |
14 |
Neural network–based modeling to predict residual stresses during electric discharge machining of Al/SiC metal matrix composites
|
Sidhu, Sarabjeet Singh |
|
2013 |
227 |
11 |
p. 1679-1692 |
artikel |
15 |
Tool wear when tapping operation of compacted graphite iron
|
da Mota, Paulo R |
|
2013 |
227 |
11 |
p. 1704-1713 |
artikel |