nr |
titel |
auteur |
tijdschrift |
jaar |
jaarg. |
afl. |
pagina('s) |
type |
1 |
A comparative study of lubricated friction and wear behaviour of Al–25Zn–3Cu–3Si bearing alloy
|
Bican, Osman |
|
2014 |
|
8 |
p. 896-903 |
artikel |
2 |
A hybrid model for multiscale simulations of nanoindentation
|
Zhu, P-Z |
|
2011 |
|
8 |
p. 845-853 |
artikel |
3 |
A microfluidic device for three-dimensional wear debris imaging in online condition monitoring
|
Peng, Yeping |
|
2017 |
|
8 |
p. 965-974 |
artikel |
4 |
A model of friction reduction with in-plane high-frequency vibration
|
Qu, Huajie |
|
2016 |
|
8 |
p. 962-967 |
artikel |
5 |
Analysis of whirling motion for the dynamic system of floating ring seal and rotor
|
Xia, Peng |
|
2019 |
|
8 |
p. 1221-1235 |
artikel |
6 |
Analysis on design parameters of water-lubricated journal bearings under hydrodynamic lubrication
|
Gao, Gengyuan |
|
2016 |
|
8 |
p. 1019-1029 |
artikel |
7 |
A new approach for closed-form analytical solution of two-dimensional symmetric double contacts and the comparison with finite element method
|
Ghanati, Parisa |
|
2018 |
|
8 |
p. 1025-1035 |
artikel |
8 |
A new approach for the optimization of the thermo-mechanical behaviour of dry-running clutches using fibre-optic sensing technology with high spatial measurement density
|
Jonas, Kniel |
|
2015 |
|
8 |
p. 1003-1010 |
artikel |
9 |
An experimental and modeling assessment of the HCFC-R123 refrigerant capabilities for lubricating rolling EHD circular contacts
|
Vergne, Philippe |
|
2015 |
|
8 |
p. 950-961 |
artikel |
10 |
Angular contact ball bearing experimental spall propagation observations
|
French, Michael L |
|
2015 |
|
8 |
p. 902-916 |
artikel |
11 |
An investigation of worn work roll materials used in the finishing stands of the hot strip mill for steel rolling
|
Nilsson, M |
|
2013 |
|
8 |
p. 837-844 |
artikel |
12 |
Application of a forecasting coupling method to the non-linear dynamic analysis of a flexible rotor supported by externally pressurized orifices hybrid gas bearings
|
Guang-hui, Z |
|
2011 |
|
8 |
p. 704-717 |
artikel |
13 |
Application of finite element method to analysis of tribological properties of aluminum oxide nano-layers
|
Kubica, M |
|
2013 |
|
8 |
p. 861-867 |
artikel |
14 |
Application of the fluid–structure interaction technique for the analysis of hydrodynamic lubrication problems
|
Wodtke, Michał |
|
2013 |
|
8 |
p. 888-897 |
artikel |
15 |
A study of indentation rolling resistance to motion of conveyor belts using a generalized Maxwell model of the backing material
|
Lu, Yan |
|
2016 |
|
8 |
p. 1006-1018 |
artikel |
16 |
A theoretical investigation of the use of 2k factorial analysis to determine the effects of dimensional manufacturing tolerances on the stability of hydrodynamic journal bearing systems
|
Ogrodnik, P J |
|
2011 |
|
8 |
p. 731-739 |
artikel |
17 |
Bearing fault diagnosis based on the dimension–temporal information
|
Zhang, D D |
|
2011 |
|
8 |
p. 806-813 |
artikel |
18 |
Biomimetic surface design for ultrahigh molecular weight polyethylene to improve the tribological properties
|
Zhang, Bo |
|
2012 |
|
8 |
p. 705-713 |
artikel |
19 |
Braking performance and influence of microstructure of advanced cast irons for heavy goods vehicle brake discs
|
Collignon, Mathilde |
|
2013 |
|
8 |
p. 930-940 |
artikel |
20 |
Calculation of eddy current loss for magnetic thrust bearings
|
Tian, Y-S |
|
2011 |
|
8 |
p. 798-805 |
artikel |
21 |
Centrifugal effects on the dynamic characteristics of high speed hydrostatic thrust bearing lubricated by low viscosity fluid
|
Wang, Lei |
|
2014 |
|
8 |
p. 860-871 |
artikel |
22 |
Characterization and properties of low-friction, multilayered Cr-doped diamond-like carbon coatings prepared by pulse biased filtered cathodic arc deposition
|
Bujak, J |
|
2011 |
|
8 |
p. 875-882 |
artikel |
23 |
Comparison of tribological performance of roller follower and flat follower under mixed elastohydrodynamic lubrication regime
|
Torabi, Amir |
|
2017 |
|
8 |
p. 986-996 |
artikel |
24 |
Confirmation of performance and reliability of direct lubricated tilting two pads bearing
|
Sano, T |
|
2015 |
|
8 |
p. 1011-1021 |
artikel |
25 |
Discussion
|
|
|
2015 |
|
8 |
p. 1039-1040 |
artikel |
26 |
Effect of Al/Ti ratio on the mechanical properties and tribological behaviours of TiAlN coatings deposited by multi-arc ion plating method
|
Zhang, J |
|
2011 |
|
8 |
p. 854-863 |
artikel |
27 |
Effect of applied pressure on high-stress abrasive wear behavior of hybrid Al–Mg–Si composites
|
Kaushik, N Ch |
|
2017 |
|
8 |
p. 1089-1100 |
artikel |
28 |
Effect of cylinder de-activation on the tribological performance of compression ring conjunction
|
Bewsher, SR |
|
2017 |
|
8 |
p. 997-1006 |
artikel |
29 |
Effect of extreme contact load under two different rotational speeds on reduced phosphorus plain ZDDP oil in the presence of 1 per cent FeF3 catalyst
|
Nehme, G |
|
2011 |
|
8 |
p. 833-844 |
artikel |
30 |
Effect of lubricant rheology on friction in coated elastohydrodynamic lubricated contacts
|
Habchi, W |
|
2017 |
|
8 |
p. 975-985 |
artikel |
31 |
Effect of oil starvation on the surface dimple in elastohydrodynamic lubrication contact under opposite sliding conditions
|
Meng, Xianghua |
|
2017 |
|
8 |
p. 1016-1029 |
artikel |
32 |
Effect of the vibration on friction and wear behavior between the carbon strip and copper contact wire pair
|
Yang, HJ |
|
2012 |
|
8 |
p. 722-728 |
artikel |
33 |
Effects of microsize SiC, Al2O3, and ZnO particulates on mechanical and tribological properties of synthesized ortho- and meta-cresol novolac epoxy composites
|
Dass, Kali |
|
2014 |
|
8 |
p. 881-895 |
artikel |
34 |
Effects of off-sized cylindrical rollers on the static load distribution in a cylinder roller bearing
|
Chen, Guanci |
|
2012 |
|
8 |
p. 687-696 |
artikel |
35 |
Effects of texture patterns on hydrodynamic and mixed lubrication characteristics
|
Imai, Norio |
|
2013 |
|
8 |
p. 898-904 |
artikel |
36 |
Experimental and numerical investigation on thermodynamic performance of full-floating ring bearings with circumferential oil groove
|
Zhang, Congcong |
|
2019 |
|
8 |
p. 1182-1196 |
artikel |
37 |
Experimental determination of heat partition in elastohydrodynamic contacts
|
Al-Hamood, Amjad |
|
2015 |
|
8 |
p. 940-949 |
artikel |
38 |
Experimental investigation of cage motions in an angular contact ball bearing
|
Wen, Baogang |
|
2017 |
|
8 |
p. 1041-1055 |
artikel |
39 |
Experimental investigation on tribological behaviour of Al-TiCp composite under sliding wear conditions
|
Josyula, Sravan Kumar |
|
2016 |
|
8 |
p. 919-929 |
artikel |
40 |
Experimental investigations of tribological performances of novel friction pair with different conical configurations
|
Wu, Xiangyu |
|
2019 |
|
8 |
p. 1245-1255 |
artikel |
41 |
Experimental study of novel clutch utilizing self-locking property of belt
|
Imado, Keiji |
|
2013 |
|
8 |
p. 912-918 |
artikel |
42 |
Fast thermo-elasto-hydrodynamic modeling approach for mixed lubricated journal bearings in internal combustion engines
|
Lorenz, Norbert |
|
2015 |
|
8 |
p. 962-976 |
artikel |
43 |
Finite element modelling of a single-particle impact during abrasive waterjet milling
|
Anwar, S |
|
2011 |
|
8 |
p. 821-832 |
artikel |
44 |
Friction and wear of a polyurethane elastomer used in dewatering for bi-directional pipeline inspection gages
|
Zhang, Hang |
|
2017 |
|
8 |
p. 1068-1077 |
artikel |
45 |
Friction characteristics of magneto-rheological fluid on DLC- and PTFE-coated surfaces
|
Zhang, Peng |
|
2017 |
|
8 |
p. 1007-1015 |
artikel |
46 |
Friction fade-out at polymer-like carbon films slid by ZrO2 pins under hydrogen environment
|
Nosaka, Masataka |
|
2015 |
|
8 |
p. 1030-1038 |
artikel |
47 |
Fundamentals of thermal elastohydrodynamic lubrication in Si3N4 and steel circular contacts
|
Kaneta, Motohiro |
|
2015 |
|
8 |
p. 929-939 |
artikel |
48 |
Identification of stiffness and damping coefficients of hydrostatic bearing with angled injection
|
Jolly, Pascal |
|
2013 |
|
8 |
p. 905-911 |
artikel |
49 |
Impact-abrasion wear of wear-resistant steels at perpendicular and tilted angles
|
Ratia, Vilma |
|
2013 |
|
8 |
p. 868-877 |
artikel |
50 |
Impact of superficial surface texture anisotropy in helical slide and plateau honing on ring-pack performance
|
Demirci, Ibrahim |
|
2016 |
|
8 |
p. 1030-1037 |
artikel |
51 |
Improvement of journal bearing operation at heavy misalignment using bearing flexibility and compliant liners
|
Thomsen, Kim |
|
2012 |
|
8 |
p. 651-660 |
artikel |
52 |
Improvement of the tribological properties of pure Ti by laser cladding intermetallic compound composite coating
|
Guo, C |
|
2011 |
|
8 |
p. 864-874 |
artikel |
53 |
Influence factors on bulk temperature field of gear
|
Luo, Biao |
|
2017 |
|
8 |
p. 953-964 |
artikel |
54 |
Influence of dynamic behaviour on elastohydrodynamic lubrication of spur gears
|
Li, S |
|
2011 |
|
8 |
p. 740-753 |
artikel |
55 |
Influence of grain boundary cementite induced by gas nitriding on the rolling contact fatigue of alloyed steels for gears*
|
Le, Marion |
|
2015 |
|
8 |
p. 917-928 |
artikel |
56 |
In situ oil flow measurements in fired engine compared to one-dimensional lube circuit simulation
|
Le Négrate, A |
|
2011 |
|
8 |
p. 762-771 |
artikel |
57 |
Introduction
|
|
|
2015 |
|
8 |
p. 883-885 |
artikel |
58 |
Investigation of fretting fatigue behaviour under multiaxial non-proportional loading
|
Liu, B |
|
2011 |
|
8 |
p. 754-761 |
artikel |
59 |
Investigation of tool geometry in nanoscale cutting single-crystal copper by molecular dynamics simulation
|
Dai, Houfu |
|
2019 |
|
8 |
p. 1208-1220 |
artikel |
60 |
Mechanical and electrical characteristics of traveling wave ultrasonic motors during the whole life of friction material
|
Li, Jinbang |
|
2016 |
|
8 |
p. 907-918 |
artikel |
61 |
Microstructure and dry sliding wear properties of 3Si–2Ni and 3Si–2Mn powder metallurgy steels with different graphite content
|
Tekeli, S |
|
2011 |
|
8 |
p. 814-820 |
artikel |
62 |
Mixed elastohydrodynamic lubrication line-contact formulas with different surface patterns
|
Masjedi, M |
|
2014 |
|
8 |
p. 849-859 |
artikel |
63 |
Numerical analysis of spiral grooved opposed-hemisphere gas bearings: A parametric study
|
Guangwei, Yang |
|
2016 |
|
8 |
p. 930-943 |
artikel |
64 |
Numerical modeling and analysis of the noncontacting impulse gas face seals
|
Blasiak, Slawomir |
|
2019 |
|
8 |
p. 1139-1153 |
artikel |
65 |
Numerical modeling of lubrication of piston ring of two-stroke marine diesel engine considering the effect of multi-scale grooves on the cylinder liner
|
Mohamad, Salaheldin A |
|
2015 |
|
8 |
p. 989-1002 |
artikel |
66 |
Numerical study of parametric effects on joint wear in the flexible multibody systems with different flexibilities and clearance sizes
|
Zhao, Bo |
|
2014 |
|
8 |
p. 819-835 |
artikel |
67 |
Optimized statistical parameters of acoustic emission signals for monitoring of rolling element bearings
|
Hemmati, Farzad |
|
2016 |
|
8 |
p. 897-906 |
artikel |
68 |
Parametric analysis of wear factors of a wet clutch friction material with different groove patterns
|
Li, M |
|
2017 |
|
8 |
p. 1056-1067 |
artikel |
69 |
Parametric study on static and dynamic characteristics of bump-type gas foil thrust bearing for oil-free turbomachinery
|
Feng, Kai |
|
2016 |
|
8 |
p. 944-961 |
artikel |
70 |
Path-dependent analysis of elastic sphere contact subjected to tangential loading with varying directions
|
Huang, Shiping |
|
2012 |
|
8 |
p. 678-686 |
artikel |
71 |
Piston ring performance in two-stroke marine diesel engines: Effect of hydrophobicity and artificial surface texturing on power efficiency
|
Koukoulopoulos, Eleftherios |
|
2018 |
|
8 |
p. 940-963 |
artikel |
72 |
Planning surface texturing for reduced friction in lubricated sliding using surface roughness parameters skewness and kurtosis
|
Sedlaček, M |
|
2012 |
|
8 |
p. 661-667 |
artikel |
73 |
Power loss prediction: Application to a 2.5 MW wind turbine gearbox
|
Fernandes, Carlos MCG |
|
2016 |
|
8 |
p. 983-995 |
artikel |
74 |
Preload effects on the static performance of multi-lobe fixed profile journal bearings with micropolar fluids
|
Rahmatabadi, A D |
|
2011 |
|
8 |
p. 718-730 |
artikel |
75 |
Role of surfactant head group and chain length in aqueous lubrication: Steel−steel contact
|
Kumar, Deepak |
|
2016 |
|
8 |
p. 968-973 |
artikel |
76 |
Sequential simulation of thermal stresses in disc brakes for repeated braking
|
Rashid, Asim |
|
2013 |
|
8 |
p. 919-929 |
artikel |
77 |
Size distribution analysis of wear particles in the transmission system of mining equipment
|
Kumar, Ashwani |
|
2018 |
|
8 |
p. 921-926 |
artikel |
78 |
Sliding friction and wear behavior of thermoplastic polyimide composites filled with differently surface-treated poly-p-phenylenebenzobisoxazole fibers
|
Yu, Liang |
|
2012 |
|
8 |
p. 697-704 |
artikel |
79 |
Special Issue: Selected papers from the 15th Nordic Symposium on Tribology
|
Armada, Sergio |
|
2013 |
|
8 |
p. 809-810 |
artikel |
80 |
Squeeze film lubrication in piston rings and reciprocating contacts
|
Taylor, RI |
|
2015 |
|
8 |
p. 977-988 |
artikel |
81 |
Static characteristics of hydrostatic doubled-layered porous journal bearings with slip flow including additives percolation into pores under coupled stress lubrication
|
Some, Shitendu |
|
2018 |
|
8 |
p. 927-939 |
artikel |
82 |
Steady state and dynamic characteristics for guide bearings of a hydro-electric unit
|
Simmons, Gregory F |
|
2014 |
|
8 |
p. 836-848 |
artikel |
83 |
41st Leeds-Lyon Symposium on Tribology
|
|
|
2015 |
|
8 |
p. 1041-1044 |
artikel |
84 |
Study on dynamic characteristics of gas films of spherical spiral groove hybrid gas bearings
|
Jia, Chenhui |
|
2019 |
|
8 |
p. 1169-1181 |
artikel |
85 |
Study on the microstructure and properties of graphite-like carbon films deposited by unbalanced magnetron sputtering
|
Wang, Yongjun |
|
2012 |
|
8 |
p. 714-721 |
artikel |
86 |
Study on tribological performances of MoS2 coating at high temperature
|
Meng, Fanming |
|
2018 |
|
8 |
p. 964-973 |
artikel |
87 |
Synergistic effect between organic borate esters and phosphorus-based additives on tribological performances as lubricant additives in mineral oil
|
Fu, Xisheng |
|
2017 |
|
8 |
p. 1030-1040 |
artikel |
88 |
Synergistic effect of Al2O3/TiO2 reinforcements on slurry erosion performance of nickel-based composite coatings
|
Kumar, Rajeev |
|
2018 |
|
8 |
p. 974-986 |
artikel |
89 |
Temperature-dependent changes of physicochemical and tribological properties of acrylonitrile-butadiene rubber elastomer upon ageing in hexadecane and diethylene glycol dibutyl ether
|
Wang, Zhou |
|
2013 |
|
8 |
p. 826-836 |
artikel |
90 |
The application of ceramic technology in spherical pipe joints
|
Yong, Zhang |
|
2017 |
|
8 |
p. 1078-1088 |
artikel |
91 |
The effect of dimple shapes on friction of parallel surfaces
|
Yu, H |
|
2011 |
|
8 |
p. 693-703 |
artikel |
92 |
The effect of microstructure and lead content on the tribological properties of bearing alloys
|
Ruusila, V |
|
2013 |
|
8 |
p. 878-887 |
artikel |
93 |
The effect of particle size on the dispersion and wear protection ability of MoS2 particles in polyalphaolefin and trimethylolpropane ester
|
Gulzar, M |
|
2018 |
|
8 |
p. 987-998 |
artikel |
94 |
The effects of diesel contaminants on tribological performance on sliding steel on steel contacts
|
Penchaliah, R |
|
2011 |
|
8 |
p. 779-797 |
artikel |
95 |
The friction and wear behavior of WC coating on medical grade titanium alloys
|
Luo, Yong |
|
2013 |
|
8 |
p. 845-849 |
artikel |
96 |
The influence of the angular distribution of a grooved surface texturing on the generation of friction-induced vibration and noise
|
Liu, MQ |
|
2018 |
|
8 |
p. 1036-1045 |
artikel |
97 |
The limiting load-carrying capacity of foil thrust bearings
|
Samanta, P |
|
2018 |
|
8 |
p. 1046-1052 |
artikel |
98 |
Theoretical analysis of a rolling-sliding elastohydrodynamic lubrication line contact with a subsurface inclusion
|
Félix Quiñonez, Armando |
|
2019 |
|
8 |
p. 1197-1207 |
artikel |
99 |
Thermal and efficiency characterization of a low-backlash planetary gearbox: An integrated numerical-analytical prediction model and its experimental validation
|
Concli, Franco |
|
2016 |
|
8 |
p. 996-1005 |
artikel |
100 |
The rolling contact fatigue of WC/C-coated spur gears
|
Michalczewski, Remigiusz |
|
2013 |
|
8 |
p. 850-860 |
artikel |
101 |
The use of equivalent estimation designs in tribological studies
|
Bochterle, Martin |
|
2015 |
|
8 |
p. 1022-1029 |
artikel |
102 |
Tribological behavior of in-situ (Cr, Mo)/Fe3Al-20 wt.%Al2O3 composites at elevated temperatures
|
Bai, Yaping |
|
2014 |
|
8 |
p. 904-912 |
artikel |
103 |
Tribological behaviors of three novel imidazoline-type thiadiazole derivatives as multifunctional lubricant additives in biodegradable lithium grease
|
Chen, Huan |
|
2012 |
|
8 |
p. 668-677 |
artikel |
104 |
Tribological behaviour of polymeric materials in water-lubricated contacts
|
Golchin, A |
|
2013 |
|
8 |
p. 811-825 |
artikel |
105 |
Tribological compatibility analysis of conventional lubricant additives with palm trimethylolpropane ester (TMP) and tetrahedral amorphous diamond-like carbon coating (ta-C)
|
Zahid, Rehan |
|
2018 |
|
8 |
p. 999-1013 |
artikel |
106 |
Tribological effects of chlorine-free lubricant in strip drawing of advanced high strength steel
|
Jewvattanarak, Phanuwat |
|
2016 |
|
8 |
p. 974-982 |
artikel |
107 |
Tribological properties of glass fibre-reinforced Nylon 66 and quenched ductile iron against Al2O3 counterpart under oilfield water lubrication
|
An, J |
|
2011 |
|
8 |
p. 772-778 |
artikel |
108 |
Tribological properties of TiN/diamond and TiAlN/diamond bilayer films sliding against carbon steel
|
Lei, Xuelin |
|
2018 |
|
8 |
p. 1014-1024 |
artikel |
109 |
Tribological response of MoS2 coated and oxy-nitrided samples with alternative extreme pressure and anti-wear additives
|
Khan, Thawhid |
|
2019 |
|
8 |
p. 1256-1273 |
artikel |
110 |
Tribo-performance of plasma-sprayed nanostructured yttria-stabilized zirconia coatings using Taguchi’s experimental design
|
Mantry, S |
|
2014 |
|
8 |
p. 872-880 |
artikel |
111 |
Understanding white etching cracks in rolling element bearings: Formation mechanisms and influent tribochemical drivers
|
Ruellan, Arnaud |
|
2015 |
|
8 |
p. 886-901 |
artikel |
112 |
Vacuum tribological properties of a composite Mo–MoS2film after atomic oxygen exposure irradiation
|
Ma, Guo-zheng |
|
2019 |
|
8 |
p. 1236-1244 |
artikel |
113 |
Viscosity behaviour and thermal conductivity prediction of CuO-blend oil based nano-blended lubricant
|
Katpatal, Dhananjay C |
|
2019 |
|
8 |
p. 1154-1168 |
artikel |