nr |
titel |
auteur |
tijdschrift |
jaar |
jaarg. |
afl. |
pagina('s) |
type |
1 |
A Comparative Study of Contact Temperature Models for Selected Sliding Pairs
|
Sardar, Santanu |
|
|
76 |
6 |
p. 1661-1675 |
artikel |
2 |
A Feasible Route to Produce 30 MPa Adhesion Strength of Electrochemically Deposited Hydroxyapatite (HA) on Titanium (Ti6Al4V) Alloy
|
Awan, Nosheen Maryam |
|
|
76 |
6 |
p. 1653-1660 |
artikel |
3 |
Al2O3 Extraction From Tailings-Containing Aluminosilicates by Pre-leaching Roasting Process–A Review
|
Mansouri, Mohammad |
|
|
76 |
6 |
p. 1393-1401 |
artikel |
4 |
A Novel Method of Preparing Gadolinium Oxide by Citric Acid-Assisted Ultrasonic Spray Pyrolysis
|
Lei, Xiang |
|
|
76 |
6 |
p. 1615-1623 |
artikel |
5 |
A Review of Ultrasonic Testing Applications in Spot Welding: Defect Evaluation in Experimental and Simulation Results
|
Mirmahdi, Esmaeil |
|
|
76 |
6 |
p. 1381-1392 |
artikel |
6 |
Boron Containing Low Carbon Deep Drawing Continuous Annealed Steel Sheet with Improved Plastic Anisotropy
|
Deva, Anjana |
|
|
76 |
6 |
p. 1487-1493 |
artikel |
7 |
Effect of Drying Route and Sintering Temperature on Zirconia Nanoparticle Synthesis for Filler Application in Polymer Composites
|
Prakash, Ved |
|
|
76 |
6 |
p. 1475-1486 |
artikel |
8 |
Effect of Filler Wire Composition on Hot-Dip Galvanizing Performance of S355JR Structural Steel Joints
|
Arabacı, Uğur |
|
|
76 |
6 |
p. 1583-1591 |
artikel |
9 |
Effect of Machining Damage on the Tensile, Flexural, and Compressive Characteristics of the Undrilled and Open-Hole Carbon Fiber-Reinforced Polymer Laminated Composites
|
Emrahi, Reza |
|
|
76 |
6 |
p. 1415-1426 |
artikel |
10 |
Effect of Single-Pass and Overlapping Laser Surface Melting Process on Microstructure and Microhardness of AISI 431 Duplex Steel
|
Shirzadi, Alireza |
|
|
76 |
6 |
p. 1643-1652 |
artikel |
11 |
Efficacy of Pilot Scale Batac Jig on LVC Coal Utilization for Coke Making
|
Andavarapu, Mohana Rao |
|
|
76 |
6 |
p. 1553-1561 |
artikel |
12 |
Erosion Wear Behavior of High Chromium Cast Irons
|
Rajicic, Bratislav M. |
|
|
76 |
6 |
p. 1427-1437 |
artikel |
13 |
Experimental Investigation of the Mechanical Properties and Tribological Behaviour of Al6061 Enhanced by TiB2 Particles
|
Hassan, Khoshy H. |
|
|
76 |
6 |
p. 1625-1633 |
artikel |
14 |
Facile Synthesis of CeO2 Nanosheets via a Parallel Flow Precipitation Route
|
Ran, Jianfeng |
|
|
76 |
6 |
p. 1495-1507 |
artikel |
15 |
Failure Analysis of High-Strength Friction-Grip (HSFG) Bolt Used in the Thermal Power Plant
|
Gurunathan, Vimalan |
|
|
76 |
6 |
p. 1593-1603 |
artikel |
16 |
First-Principles Investigation on the High-Temperature Mechanical Properties and Thermal Properties of Pt-40Rh
|
Wei, Yan |
|
|
76 |
6 |
p. 1545-1552 |
artikel |
17 |
Influence of Fly Ash Particles on Machining Characteristics of AA6061 Aluminum Matrix Composites Produced Using Semisolid Slurry Casting
|
Dinaharan, Isaac |
|
|
76 |
6 |
p. 1447-1452 |
artikel |
18 |
Influence of Gd Concentration on the Structural, Optical, and Electrical Properties of Gd/Al Codoped TiO2Nanoparticles by Precipitation Method
|
Ashoor, H. E. |
|
|
76 |
6 |
p. 1685-1690 |
artikel |
19 |
Investigating the Wear Resistance of 18Ni300 Steel Reinforced by Nanostructured WC Particles Using Molecular Dynamics Simulations and Experiments
|
Jiang, Chunlin |
|
|
76 |
6 |
p. 1635-1642 |
artikel |
20 |
Investigation of the Structural, Tribological, and Electrochemical Properties of Nitrided and Boronized AISI 316L Stainless Steel
|
Çakır, Mevra Aslan |
|
|
76 |
6 |
p. 1517-1533 |
artikel |
21 |
Magnesium Chloride Crystals with Studying Mechanism and Leaching Kinetics of Serpentinite Ore by Hydrochloric Acid
|
El-Sayed, D. |
|
|
76 |
6 |
p. 1439-1446 |
artikel |
22 |
Microstructure and Mechanical Properties of an Er-Modified Al–Mg–Mn–Sc–Zr Alloy Processed by Selective Laser Melting
|
Shi, Jinglin |
|
|
76 |
6 |
p. 1605-1614 |
artikel |
23 |
Prediction of Porosity and Hot Tearing in Direct Chill Casting of AZ31 Magnesium Alloy
|
Sai Divya, P. V. |
|
|
76 |
6 |
p. 1509-1516 |
artikel |
24 |
Replacement of Cu with One-Step Production of CuAg (Ag0.04Cu3.96): Superior Conductivity, Corrosion Resistance, and Hardness
|
Cihangir, Salih |
|
|
76 |
6 |
p. 1403-1413 |
artikel |
25 |
Research on Repairing Edge of Trimming Die with Arc Welding Robot
|
Liu, Shuaiqi |
|
|
76 |
6 |
p. 1573-1581 |
artikel |
26 |
Silver and Copper Coating Effects on Surface Morphology, Crystal Structure and Corrosion Behavior of NiTinol Shape Memory Alloy Plate
|
Say, Yakup |
|
|
76 |
6 |
p. 1563-1572 |
artikel |
27 |
Study on the Interface of Molybdenum Foil-copper Explosive-welded Composite Plate
|
Bi, Zhixiong |
|
|
76 |
6 |
p. 1677-1684 |
artikel |
28 |
The Cu/Nb Ratio Influencing Microstructure, Mechanical and Electrical Properties in As-cast Al-3Cu-xNb Alloys
|
Mendes, Gabriel |
|
|
76 |
6 |
p. 1453-1465 |
artikel |
29 |
The Effect of Microstructure Size on Microstructure and Properties of High Boron Alloy During Quenching and Partitioning (Q&P) Process
|
Li, Zhao |
|
|
76 |
6 |
p. 1535-1543 |
artikel |
30 |
The Hot Deformation Behavior and Microstructural Evolution of TP2 Pure Copper
|
Zhao, Haitao |
|
|
76 |
6 |
p. 1467-1474 |
artikel |