nr |
titel |
auteur |
tijdschrift |
jaar |
jaarg. |
afl. |
pagina('s) |
type |
1 |
Adhesion Behaviour, Nanohardness and Surface Roughness of Ti–6Al–4V–6B4C Thin Films Grown on AISI 1040 Steel
|
Selvakumar, N. |
|
2017 |
71 |
4 |
p. 893-899 |
artikel |
2 |
1060 Al Electric Hot Incremental Sheet Forming Process: Analysis of Dimensional Accuracy and Temperature
|
Li, Zhengfang |
|
2017 |
71 |
4 |
p. 961-970 |
artikel |
3 |
A New Hot Tearing Assessment by Using Stepped Ring Core Mold and the Effect of Strontium on the Hot-Tearing Resistance of Al–6 wt% Zn Based Alloy
|
Sujith, S. V. |
|
2017 |
71 |
4 |
p. 923-934 |
artikel |
4 |
Characterization and Reduction Roasting Studies of an Iron Rich Manganese Ore
|
Rath, Swagat S. |
|
2017 |
71 |
4 |
p. 861-872 |
artikel |
5 |
Comparison of Continuum Damage Laws Under Uniaxial Creep for an AISI 316 Stainless Steel
|
Ranjekar, Tejas |
|
2017 |
71 |
4 |
p. 935-940 |
artikel |
6 |
Construction of Phase Diagrams for AlxHfNbTaTiZr Refractory High Entropy Alloy
|
Anilkumar, Sana |
|
2017 |
71 |
4 |
p. 901-907 |
artikel |
7 |
Effect of Annealing Temperature on Punching Shear Strength of Nb-A286 Superalloy
|
Sahrapour, Peyman |
|
2017 |
71 |
4 |
p. 1003-1010 |
artikel |
8 |
Effect of Filler Metal Mechanical Properties on Fatigue Behaviour Welded Joints
|
Alioua, Abdelkader |
|
2017 |
71 |
4 |
p. 977-984 |
artikel |
9 |
Effect of Speed on the Tribological Behavior of Fe–Cu–C Based Self Lubricating Composite
|
Sharma, Sanjay Mohan |
|
2017 |
71 |
4 |
p. 883-891 |
artikel |
10 |
Effect of Temper Conditions on Abrasive Wear Behavior of AA7010 Alloy
|
Mahajan, Yogesh |
|
2017 |
71 |
4 |
p. 1025-1032 |
artikel |
11 |
Effects of Different Heat Treatments on Microstructure, Toughness and Wear Behavior of G-X 10CrNiMoNb 18-10 Cast Austenitic Stainless Steel
|
Türker, Mehmet |
|
2017 |
71 |
4 |
p. 1033-1040 |
artikel |
12 |
Improvement of Microstructure, Mechanical Properties and Corrosion Resistance of Cast Al–12Si Alloy by Friction Stir Processing
|
Sun, HuanHuan |
|
2017 |
71 |
4 |
p. 985-991 |
artikel |
13 |
Investigation of Mechanical Properties and Dry Sliding Wear Behaviour of Squeeze Cast LM6 Aluminium Alloy Reinforced with Copper Coated Short Steel Fibers
|
Chelladurai, Samson Jerold Samuel |
|
2017 |
71 |
4 |
p. 813-822 |
artikel |
14 |
Investigation of Microstructure, Mechanical and Wear Behaviour of B4C Particulate Reinforced Magnesium Matrix Composites by Powder Metallurgy
|
Aydin, Fatih |
|
2017 |
71 |
4 |
p. 873-882 |
artikel |
15 |
Investigation of Microstructure Properties and Quantitative Metallography by Different Etchants in the Service-Exposed Nickel-Based Superalloy Turbine Blade
|
Khodabakhshi, Amirhossein |
|
2017 |
71 |
4 |
p. 849-859 |
artikel |
16 |
Machining Characteristics and Corrosion Behavior of Grain Refined AZ91 Mg Alloy Produced by Friction Stir Processing: Role of Tool Pin Profile
|
Patle, Hemendra |
|
2017 |
71 |
4 |
p. 951-959 |
artikel |
17 |
Mechanical Properties of a Ni–Cr–Mo Steel Subjected to Room Temperature Carburizing Using Surface Mechano-Chemical Carburizing Treatment (SMCT)
|
Sahu, Jogindra Nath |
|
2017 |
71 |
4 |
p. 915-921 |
artikel |
18 |
Microstructural and Mechanical Properties of FSW Joints Between AA6101-T6 and AA6351-T6 Dissimilar Al Alloys
|
Das, U. |
|
2017 |
71 |
4 |
p. 823-830 |
artikel |
19 |
Multi-objective Optimization of Cold Upsetting Parameters for Aluminium Metal Matrix Composites
|
Shantharaman, P. P. |
|
2017 |
71 |
4 |
p. 909-914 |
artikel |
20 |
60NiTi: A Review of Recent Research Findings, Potential for Structural and Mechanical Applications, and Areas of Continued Investigations
|
Khanlari, Khashayar |
|
2017 |
71 |
4 |
p. 781-799 |
artikel |
21 |
Optimizing Process Parameters for Increasing Corrosion Resistance of Friction Stir Spot Welded Dissimilar Al-5086/C10100 Joints
|
Siddharth, S. |
|
2017 |
71 |
4 |
p. 1011-1024 |
artikel |
22 |
Reaction Kinetics at the Fiber/Matrix Interface of SiCf/Ti–15–3 Composites
|
Muthuchamy, A. |
|
2017 |
71 |
4 |
p. 941-949 |
artikel |
23 |
Research on High Speed Machining of TC17 Titanium Alloy Under Extreme Environments
|
Ping, Zhang |
|
2017 |
71 |
4 |
p. 831-839 |
artikel |
24 |
Studies on 7075 Aluminium Alloy MMCs with Milled Carbon Fibers as Reinforcements
|
Deshpande, Madhuri |
|
2017 |
71 |
4 |
p. 993-1002 |
artikel |
25 |
Synthesis, Characterization and Mechanical Properties of AA7075 Based MMCs Reinforced with TiB2 Particles Processed Through Ultrasound Assisted In-Situ Casting Technique
|
Meti, Vinod Kumar V. |
|
2017 |
71 |
4 |
p. 841-848 |
artikel |
26 |
The Effect of Inner Corner Radius of ECAP Die on Strain Distribution and Damage Accumulation in Deformed Sample
|
Ghazani, Mehdi Shaban |
|
2017 |
71 |
4 |
p. 971-976 |
artikel |
27 |
Viscosity of Industrial Blast Furnace Slag in Indian Scenario
|
Pati, A. |
|
2017 |
71 |
4 |
p. 801-812 |
artikel |