nr |
titel |
auteur |
tijdschrift |
jaar |
jaarg. |
afl. |
pagina('s) |
type |
1 |
A Study on Cutting Characteristics in Turning Operations of Titanium Alloy used in Automobile
|
You, Seung Hyeon |
|
2019 |
20 |
2 |
p. 209-216 |
artikel |
2 |
Au Nanoparticle Array Deposited Phase-Change Material for Optical Information Recording Using Field Enhancement Based on Localized Surface Plasmon Resonance
|
Kang, Sung-Mook |
|
2019 |
20 |
2 |
p. 267-272 |
artikel |
3 |
Design of Laminated Seal in Cryogenic Triple-Offset Butterfly Valve Used in LNG Marine Engine
|
Kwak, Hyo-Seo |
|
2019 |
20 |
2 |
p. 243-253 |
artikel |
4 |
Fault Diagnosis of Planetary Gear Carrier Packs: A Class Imbalance and Multiclass Classification Problem
|
Han, Soonyoung |
|
2019 |
20 |
2 |
p. 167-179 |
artikel |
5 |
Impact Attenuation of the Soft Pads and the Wearable Airbag for the Hip Protection in the Elderly
|
Jeong, Youngjae |
|
2019 |
20 |
2 |
p. 273-283 |
artikel |
6 |
Improvement of Wire Electrical Discharge Machining Characteristics in Machining Boron-doped Polycrystalline Diamond Using a Novel Iso-pulse Generator
|
Yan, Mu-Tian |
|
2019 |
20 |
2 |
p. 159-166 |
artikel |
7 |
Methods of Improving Mechanical Integrity of Center-Link Chains for a Trolley Conveyor System
|
Han, Changwan |
|
2019 |
20 |
2 |
p. 301-312 |
artikel |
8 |
Numerical Study and Experimental Investigation on Electromagnetic Crimping for Tube-to-Rod Configuration
|
Areda, Getu Tilahun |
|
2019 |
20 |
2 |
p. 181-191 |
artikel |
9 |
Optimal Parameter Design of a Cleaning Device for Vertical Glass Surfaces
|
Hong, Jooyoung |
|
2019 |
20 |
2 |
p. 233-241 |
artikel |
10 |
Optimization of Variable Blank Holder Force Based on a Sharing Niching RBF Neural Network and an Improved NSGA-II Algorithm
|
Xie, Yanmin |
|
2019 |
20 |
2 |
p. 285-299 |
artikel |
11 |
Performance Analysis on Solar Concentrating Thermoelectric Generator Coupled with Heat Sink
|
Köysal, Yavuz |
|
2019 |
20 |
2 |
p. 313-318 |
artikel |
12 |
Research on the Cutting Performances and Wear Mechanisms of TiAlCrN Coated Tools During Dry Turning
|
He, Hui-Bo |
|
2019 |
20 |
2 |
p. 201-207 |
artikel |
13 |
Springback Analysis of the Stiffened Panel Milling from the Bent Plate
|
Liu, Chun-Guo |
|
2019 |
20 |
2 |
p. 217-232 |
artikel |
14 |
Study and Optimization of Structural Parameters of Oil Seal by Response Surface Method
|
Zhang, Fu-Ying |
|
2019 |
20 |
2 |
p. 255-265 |
artikel |
15 |
Touch Probe Tip Compensation Using a Novel Transformation Algorithm for Coordinate Measurements of Curved Surfaces
|
Ahn, Hee Kyung |
|
2019 |
20 |
2 |
p. 193-199 |
artikel |