nr |
titel |
auteur |
tijdschrift |
jaar |
jaarg. |
afl. |
pagina('s) |
type |
1 |
Analysing the Fatigue Behaviour and Residual Stress Relaxation of Gradient Nano-Structured 316L Steel Subjected to the Shot Peening via Deep Learning Approach
|
Maleki, Erfan |
|
|
28 |
1 |
p. 112-131 |
artikel |
2 |
Assessment of Process, Parameters, Residual Stress Mitigation, Post Treatments and Finite Element Analysis Simulations of Wire Arc Additive Manufacturing Technique
|
Barath Kumar, M. D. |
|
|
28 |
1 |
p. 54-111 |
artikel |
3 |
Correction to: Effects of I- and W-Phases Under Identical Conditions on Microstructure and Mechanical Properties of As-Cast Mg–Zn–Y Alloys at Room and Elevated Temperatures
|
Jung, Young-Gil |
|
|
28 |
1 |
p. 336 |
artikel |
4 |
Correction to: Selective Laser Melting Process for Sensor Embedding into SUS316L with Heat Dissipative Inner Cavity Design
|
Lee, Min Sik |
|
|
28 |
1 |
p. 306 |
artikel |
5 |
Effect of Annealing and Crack Orientation on Fatigue Crack Propagation of Ti64 Alloy Fabricated by Direct Energy Deposition Process
|
Kim, Soyoung |
|
|
28 |
1 |
p. 205-215 |
artikel |
6 |
Effects of Laser Power on the Microstructure Evolution and Mechanical Properties of Ti–6Al–4V Alloy Manufactured by Direct Energy Deposition
|
Lee, Yukyeong |
|
|
28 |
1 |
p. 197-204 |
artikel |
7 |
Equiatomic, Cu‐Containing CrCuFeTiV 3d Transition Metal High Entropy Alloy with an Enhanced Strength and Hardness Synergy
|
Yi, Jiaojiao |
|
|
28 |
1 |
p. 227-236 |
artikel |
8 |
Fabrication of Gas Metal Arc Welding Based Wire Plus Arc Additive Manufactured 347 Stainless Steel Structure: Behavioral Analysis Through Experimentation and Finite Element Method
|
Pramod, R. |
|
|
28 |
1 |
p. 307-321 |
artikel |
9 |
Influence of Nanoparticles Reinforcements on Aluminium 6061 Alloys Fabricated via Novel Ultrasonic Aided Rheo-Squeeze Casting Method
|
Arunkumar, T. |
|
|
28 |
1 |
p. 145-154 |
artikel |
10 |
Investigation of the Microstructure and Mechanical Characteristics of Lattice Structures Produced by Laser Powder Bed Fusion Method
|
Erturk, A. Tamer |
|
|
28 |
1 |
p. 155-167 |
artikel |
11 |
Laser Surface Texturing in Powder Bed Fusion: Numerical Simulation and Experimental Characterization
|
Mandal, Vijay |
|
|
28 |
1 |
p. 181-196 |
artikel |
12 |
Microstructure and Properties of 2Cr13-xMo Stainless Steels Fabricated by Direct Laser Deposition
|
Liang, Jing |
|
|
28 |
1 |
p. 216-226 |
artikel |
13 |
Microtextural Characterization of Additively Manufactured SS316L After Hot Isostatic Pressing Heat Treatment
|
Chadha, Kanwal |
|
|
28 |
1 |
p. 237-249 |
artikel |
14 |
Multiphysics Modeling of Thermal Behavior of Commercial Pure Titanium Powder During Selective Laser Melting
|
Ye, Wenlin |
|
|
28 |
1 |
p. 282-296 |
artikel |
15 |
Nanostructured Materials and Nanocomposites by Mechanical Alloying: An Overview
|
Suryanarayana, C. |
|
|
28 |
1 |
p. 41-53 |
artikel |
16 |
pyMPEALab Toolkit for Accelerating Phase Design in Multi-principal Element Alloys
|
Subedi, Upadesh |
|
|
28 |
1 |
p. 269-281 |
artikel |
17 |
Selective Laser Melting Process for Sensor Embedding into SUS316L with Heat Dissipative Inner Cavity Design
|
Lee, Min Sik |
|
|
28 |
1 |
p. 297-305 |
artikel |
18 |
Strontium in Al–Si–Mg Alloy: A Review
|
Ganesh, M. R. Sai |
|
|
28 |
1 |
p. 1-40 |
artikel |
19 |
Study of the Effect of Two Separate Tilt Angles of Laser Scanning Lines on the Microstructure and Mechanical Properties in Direct Metal Laser Sintered AlSi10Mg Alloy
|
Chakrabarty, Aniket |
|
|
28 |
1 |
p. 250-268 |
artikel |
20 |
Tensile Properties of Additively Manufactured C-18150 Copper Alloys
|
Zeng, Congyuan |
|
|
28 |
1 |
p. 168-180 |
artikel |
21 |
Uniaxial Compression Properties and Compression Fatigue Performance of Selective Laser Melted Ti–6Al–4V Cellular Structure
|
Wu, Ming-Wei |
|
|
28 |
1 |
p. 132-144 |
artikel |
22 |
Utilizing Additive Friction Stir Processing to Fabricate B4C Reinforced Ti–6Al–4V Matrix Surface Composite: Microstructure Refinement and Enhancement in Mechanical Properties
|
Deore, H. A. |
|
|
28 |
1 |
p. 322-335 |
artikel |