| no |
title |
author |
magazine |
year |
volume |
issue |
page(s) |
type |
| 1 |
Acoustic damping optimization of the injector based on dynamic mode decomposition in a subscale combustor
|
Kim, Young Jun
|
|
2017
|
31 |
9 |
p. 4511-4520
|
article
|
| 2 |
Acoustic emission characteristics of methacrylate-based composite and silorane-based composite during dental restoration according to a variety of C-factor
|
Park, Jung-Hoon
|
|
2017
|
31 |
9 |
p. 4067-4072
|
article
|
| 3 |
Aerodynamic performance optimization for the rotor design of a hovering agricultural unmanned helicopter
|
Haider, B. A.
|
|
2017
|
31 |
9 |
p. 4221-4226
|
article
|
| 4 |
A method for analysis of head cover deformation and vibration amplitude in Francis hydro-turbine system by combination of CFD and FEA
|
Jia, Yun
|
|
2017
|
31 |
9 |
p. 4255-4266
|
article
|
| 5 |
A molecular dynamics study on atomistic mechanisms of nano-scale cutting process of sapphire
|
Kim, Woo Kyun
|
|
2017
|
31 |
9 |
p. 4353-4362
|
article
|
| 6 |
Analysis and measurement of relative humidity effects on ejector performance
|
Lee, Hochae
|
|
2017
|
31 |
9 |
p. 4237-4244
|
article
|
| 7 |
Application of the ultrasonic propagation imaging system to an immersed metallic structure with a crack under a randomly oscillating water surface
|
Park, Jae-Yoon
|
|
2017
|
31 |
9 |
p. 4099-4108
|
article
|
| 8 |
Application of v-shaped magnet in inner surface polishing of tubes
|
Zhang, Yaoming
|
|
2017
|
31 |
9 |
p. 4381-4385
|
article
|
| 9 |
A study of the current density analysis for two type method on the invar alloy in electrochemical machining
|
Choi, Seung-Geon
|
|
2017
|
31 |
9 |
p. 4345-4351
|
article
|
| 10 |
A study on cycle performance variation of a linear compressor considering valve behavior
|
Park, Sang Jun
|
|
2017
|
31 |
9 |
p. 4481-4488
|
article
|
| 11 |
Calibration of hoop stress in ring tensile test with Zircaloy-4 tube
|
Yoon, J.
|
|
2017
|
31 |
9 |
p. 4183-4188
|
article
|
| 12 |
Comparison of fuel efficiency and economical speed for internal combustion engine vehicle and battery electric vehicle using backward-looking simulation
|
Lee, Hoon
|
|
2017
|
31 |
9 |
p. 4499-4509
|
article
|
| 13 |
Compensating UAV GPS data accuracy through use of relative positioning and GPS data of UGV
|
Jung, Sunghun
|
|
2017
|
31 |
9 |
p. 4471-4480
|
article
|
| 14 |
Design and investigation of a cycloid helical gear drive
|
Li, Xuan
|
|
2017
|
31 |
9 |
p. 4329-4336
|
article
|
| 15 |
Design of a bubble collecting section in a high speed water tunnel for ventilated supercavitation experiments
|
Paik, Bu-Geun
|
|
2017
|
31 |
9 |
p. 4227-4235
|
article
|
| 16 |
Design sensitivity analysis of a Stockbridge damper to control resonant frequencies
|
Kim, Chan-Jung
|
|
2017
|
31 |
9 |
p. 4145-4150
|
article
|
| 17 |
Development of high concentrated slightly acidic hypochlorous acid generator for food safety
|
Jafry, Ali Turab
|
|
2017
|
31 |
9 |
p. 4541-4547
|
article
|
| 18 |
Development of the plastic culture container to improve light transmission and stacking possibility
|
Han, Seong-Ryeol
|
|
2017
|
31 |
9 |
p. 4395-4403
|
article
|
| 19 |
Dressing process in the grinding of aerospace blade root
|
Żyłka, Łukasz
|
|
2017
|
31 |
9 |
p. 4411-4417
|
article
|
| 20 |
Effectiveness of CFRP rudder aspect ratio for scale model catamaran racing yacht test
|
Jang, Hoyun
|
|
2017
|
31 |
9 |
p. 4109-4117
|
article
|
| 21 |
Effect of pre-treatment polishing on fabrication of anodic aluminum oxide using commercial aluminum alloy
|
Kim, Ki Beom
|
|
2017
|
31 |
9 |
p. 4387-4393
|
article
|
| 22 |
Effects of nonlinear friction compensation in the inertia wheel pendulum
|
Aguilar-Avelar, Carlos
|
|
2017
|
31 |
9 |
p. 4425-4433
|
article
|
| 23 |
Effects of solution treatment and sheath on mechanical properties of Al7075 processed by ECAP
|
Ahmadi, S.
|
|
2017
|
31 |
9 |
p. 4189-4194
|
article
|
| 24 |
Effects of variable resistance on smart structures of cubic reconnaissance satellites in various thermal and frequency shocking conditions
|
Elahi, Hassan
|
|
2017
|
31 |
9 |
p. 4151-4157
|
article
|
| 25 |
Elastro-hydrodynamic lubrication model of multi-decked foil thrust bearing with copper wire support
|
Lai, Tianwei
|
|
2017
|
31 |
9 |
p. 4371-4379
|
article
|
| 26 |
Evaluation of material properties and internal damage within CFRP and CFRP/Al sandwich panels due to impact loading
|
Hosoi, Masahiro
|
|
2017
|
31 |
9 |
p. 4079-4084
|
article
|
| 27 |
Experimental and mathematical analysis of simulation results for sheet metal parts in deep drawing
|
Choubey, Ajay Kumar
|
|
2017
|
31 |
9 |
p. 4215-4220
|
article
|
| 28 |
Experimental and numerical studies on erosion damage in damping holes on the valve plate of an axial piston pump
|
Ye, Shaogan
|
|
2017
|
31 |
9 |
p. 4285-4295
|
article
|
| 29 |
Experimental investigation of in-process mitigation of welding distortion for stainless steel plate using air-atomized mist cooling
|
Joo, Sung-Min
|
|
2017
|
31 |
9 |
p. 4419-4423
|
article
|
| 30 |
Failure behavior of a composite T-joint subjected to hydrodynamic ram
|
Go, Eun-Su
|
|
2017
|
31 |
9 |
p. 4085-4091
|
article
|
| 31 |
Failure prediction of composite T-joints for hydrodynamic ram test
|
Kim, Dong-Geon
|
|
2017
|
31 |
9 |
p. 4093-4098
|
article
|
| 32 |
Fatigue life prediction of turbine blades based on a modified equivalent strain model
|
Zhou, Jie
|
|
2017
|
31 |
9 |
p. 4203-4213
|
article
|
| 33 |
Feasibility studies of laser surface nitriding on Ti-6Al-4V alloy using a nitric acid solution
|
Hwang, Tae Woo
|
|
2017
|
31 |
9 |
p. 4175-4182
|
article
|
| 34 |
Flow ripple analysis and structural parametric design of a piston pump
|
Wu, Xiaofeng
|
|
2017
|
31 |
9 |
p. 4245-4254
|
article
|
| 35 |
Global characteristics of low-flow-rate aviation fuel sprays by image processing
|
Zakaria, Rami
|
|
2017
|
31 |
9 |
p. 4267-4273
|
article
|
| 36 |
Highly efficient in-line wet cyclone air sampler for airborne virus detection
|
Sung, Giwoon
|
|
2017
|
31 |
9 |
p. 4363-4369
|
article
|
| 37 |
Highly efficient in-line wet cyclone air sampler for airborne virus detection
|
Sung, Giwoon
|
|
|
31 |
9 |
p. 4363-4369
|
article
|
| 38 |
Mean stress effects in fretting fatigue life estimation method using fatigue damage gradient correction factor
|
Hwang, Dong Hyeon
|
|
2017
|
31 |
9 |
p. 4195-4202
|
article
|
| 39 |
Mechanical property behavior and aging mechanism of carbon-black-filled EPDM rubber reinforced by carbon nano-tubes subjected to electro-chemical and thermal degradation
|
Han, Seung-Wook
|
|
2017
|
31 |
9 |
p. 4073-4078
|
article
|
| 40 |
Multibody contact dynamics on mechanisms with deep groove ball bearing joints
|
Yao, Tingqiang
|
|
2017
|
31 |
9 |
p. 4119-4135
|
article
|
| 41 |
Multi-objective parameter space approach based controller and add-on disturbance observer design
|
Emirler, Mümin Tolga
|
|
2017
|
31 |
9 |
p. 4447-4458
|
article
|
| 42 |
Numerical investigation of LNG gas dispersion in a confined space: An engineering model
|
Li, Longnan
|
|
2017
|
31 |
9 |
p. 4533-4540
|
article
|
| 43 |
Numerical simulation of holes and inclusions using adaptive polygonal finite element method
|
Ding, Shengyong
|
|
2017
|
31 |
9 |
p. 4305-4317
|
article
|
| 44 |
Numerical simulation of kink angle prediction for non-lubricated surface crack subjected to Hertzian pressure
|
Fajdiga, Gorazd
|
|
2017
|
31 |
9 |
p. 4167-4173
|
article
|
| 45 |
Numerical study of heat and mass transfer analogy for a simulated turbine endwall
|
Hamdi, F.
|
|
2017
|
31 |
9 |
p. 4275-4283
|
article
|
| 46 |
Optical study on combustion characteristics of hydrotreated vegetable oil and blends under simulated CI engine conditions and various EGR
|
Chau, Vo Tan
|
|
2017
|
31 |
9 |
p. 4521-4531
|
article
|
| 47 |
Simplified evaluation criterion for concepts of engineering design based on cost, simplicity, and safety
|
Cho, Chang-Hee
|
|
2017
|
31 |
9 |
p. 4319-4328
|
article
|
| 48 |
Stability assist wheel control of multi-axle all-terrain crane using RLS algorithms with forgetting
|
Oh, Kwangseok
|
|
2017
|
31 |
9 |
p. 4435-4446
|
article
|
| 49 |
Studies on Stewart platform manipulator: A review
|
Furqan, Mohd
|
|
2017
|
31 |
9 |
p. 4459-4470
|
article
|
| 50 |
Study on the performance of celdek packed counter flow liquid desiccant regenerator
|
Kumar, Rakesh
|
|
2017
|
31 |
9 |
p. 4489-4498
|
article
|
| 51 |
Supersonic turbine stator design using dense gas with numerical method
|
Seo, J.
|
|
2017
|
31 |
9 |
p. 4297-4303
|
article
|
| 52 |
Synchronization of pneumatic vibroexciters under air cushion operating mode in a self-exciting autovibration regime
|
Kibirkštis, Edmundas
|
|
2017
|
31 |
9 |
p. 4137-4144
|
article
|
| 53 |
Taguchi-based grey relational analysis for modeling and optimizing machining parameters through dry turning of Incoloy 800H
|
Angappan, Palanisamy
|
|
2017
|
31 |
9 |
p. 4159-4165
|
article
|
| 54 |
Temporal evolution in a dissipative air-coupled spherical dielectric elastomer actuator
|
Wang, H. M.
|
|
2017
|
31 |
9 |
p. 4337-4343
|
article
|
| 55 |
The weldability study of carbon nanotube based 2nd generation primer coated steel for automotive applications
|
Vijayan, Vijeesh
|
|
2017
|
31 |
9 |
p. 4405-4410
|
article
|
Journal description