nr |
titel |
auteur |
tijdschrift |
jaar |
jaarg. |
afl. |
pagina('s) |
type |
1 |
Bifurcation and Deviation of Cleavage Paths at Through-Thickness Grain Boundaries
|
Chen, J. |
|
2008 |
39 |
9 |
p. 2040-2044 |
artikel |
2 |
Cellular/Dendritic Transition and Microstructure Evolution during Transient Directional Solidification of Pb-Sb Alloys
|
Rosa, Daniel M. |
|
2008 |
39 |
9 |
p. 2161-2174 |
artikel |
3 |
Changes in Interface Parameters and Tensile Properties in Copper as a Consequence of Iterative Processing
|
Coleman, Mark |
|
2008 |
39 |
9 |
p. 2175-2183 |
artikel |
4 |
Consolidation and Forging Methods for a Cryomilled Al Alloy
|
Newbery, A.P. |
|
2008 |
39 |
9 |
p. 2193-2205 |
artikel |
5 |
Effect of Filler Metal Composition on the Strength of Yttria Stabilized Zirconia Joints Brazed with Pd-Ag-CuOx
|
Darsell, Jens T. |
|
2008 |
39 |
9 |
p. 2095-2105 |
artikel |
6 |
Effect of Volume Fraction of Primary α2 on the Trigger Stress for Stress-Induced Martensitic Transformation in Two-Phase Ti-Al-Nb Alloys
|
Paradkar, Archana |
|
2008 |
39 |
9 |
p. 2086-2094 |
artikel |
7 |
Effects of Changes in Test Temperature and Loading Conditions on Fracture Toughness of a Zr-Based Bulk Metallic Glass
|
Hassan, Hala A. |
|
2008 |
39 |
9 |
p. 2077-2085 |
artikel |
8 |
Equal Channel Angular Pressing of Canned 2124-Al Compacts: Processing, Experiments, and Modeling
|
Elkhodary, K.I. |
|
2008 |
39 |
9 |
p. 2184-2192 |
artikel |
9 |
Expansion Mechanisms in Foaming Aluminum Melts
|
Song, Zhenlun |
|
2008 |
39 |
9 |
p. 2215-2227 |
artikel |
10 |
Fatigue Properties of Nitrided Ultrafine Ferrite-Cementite Steels under Rotating Bending Fatigue Testing
|
Furuya, Y. |
|
2008 |
39 |
9 |
p. 2068-2076 |
artikel |
11 |
Grain Selection and Texture Evolution in Directionally Solidified Al-Zn Alloys
|
Gonzales, Frédéric |
|
2008 |
39 |
9 |
p. 2148-2160 |
artikel |
12 |
High-Temperature Oxidation of β-NbTi Alloys
|
Parida, S.C. |
|
2008 |
39 |
9 |
p. 2020-2025 |
artikel |
13 |
Influence of Cr and Ni on Microstructural Evolution during Heat Treatment of Low-Carbon Transformation Induced Plasticity Steels
|
Suh, Dong-Woo |
|
2008 |
39 |
9 |
p. 2015-2019 |
artikel |
14 |
Influence of Weld Cooling Rate on Microstructure and Mechanical Properties of Alloy 718 Weldments
|
Sivaprasad, K. |
|
2008 |
39 |
9 |
p. 2115-2127 |
artikel |
15 |
In-Situ Fracture Studies and Modeling of the Toughening Mechanism Present in Wrought Low-Carbon Arc-Cast Molybdenum, Titanium-Zirconium-Molybdenum, and Oxide-Dispersion-Strengthened Molybdenum Flat Products
|
Cockeram, B.V. |
|
2008 |
39 |
9 |
p. 2045-2067 |
artikel |
16 |
Interface Microstructure and Strength Properties of the Diffusion-Bonded Joints of Titanium ∣Cu Interlayer ∣ Stainless Steel
|
Kundu, S. |
|
2008 |
39 |
9 |
p. 2106-2114 |
artikel |
17 |
Morphology and Kinetics of Interfacial Layer Formation during Continuous Hot-Dip Galvanizing and Galvannealing
|
Chen, L. |
|
2008 |
39 |
9 |
p. 2128-2142 |
artikel |
18 |
Natural Aging in Mg-Zn(-Cu) Alloys
|
Buha, J. |
|
2008 |
39 |
9 |
p. 2259-2273 |
artikel |
19 |
Pseudoelasticity and Cyclic Stability in Co49Ni21Ga30 Shape-Memory Alloy Single Crystals at Ambient Temperature
|
Dadda, J. |
|
2008 |
39 |
9 |
p. 2026-2039 |
artikel |
20 |
Textural Development of AA 5754 Sheet Deformed under In-Plane Biaxial Tension
|
Banovic, S.W. |
|
2008 |
39 |
9 |
p. 2246-2258 |
artikel |
21 |
Thermal Behavior and Microstructural Evolution during Laser Deposition with Laser-Engineered Net Shaping: Part I. Numerical Calculations
|
Zheng, B. |
|
2008 |
39 |
9 |
p. 2228-2236 |
artikel |
22 |
Thermal Behavior and Microstructure Evolution during Laser Deposition with Laser-Engineered Net Shaping: Part II. Experimental Investigation and Discussion
|
Zheng, B. |
|
2008 |
39 |
9 |
p. 2237-2245 |
artikel |
23 |
Thickness of Anodic Titanium Oxides as a Function of Crystallographic Orientation of the Substrate
|
Diamanti, M.V. |
|
2008 |
39 |
9 |
p. 2143-2147 |
artikel |
24 |
Ultrafine Grain Formation in Ferritic Stainless Steel during Severe Plastic Deformation
|
Sakai, T. |
|
2008 |
39 |
9 |
p. 2206-2214 |
artikel |