| nr |
titel |
auteur |
tijdschrift |
jaar |
jaarg. |
afl. |
pagina('s) |
type |
| 1 |
A comparative study on the microstructure, mechanical properties, wear and corrosion behaviors of SS 316 austenitic stainless steels manufactured by casting and WAAM technologies
|
Gürol, Uğur
|
|
|
47 |
C |
p. 215-227
|
artikel
|
| 2 |
Analysis and development of elliptical tool path in trochoidal milling
|
Wagih, Mohamed
|
|
|
47 |
C |
p. 168-183
|
artikel
|
| 3 |
An uncertain multi-objective model for simultaneous design of supply chain and assemblers considering sustainable development: a case study
|
Niroomand, Sadegh
|
|
|
47 |
C |
p. 86-102
|
artikel
|
| 4 |
Corrosion behaviour of copper cladded steel produced using multi pass friction stir welding process
|
Mahto, Mithlesh Kumar
|
|
|
47 |
C |
p. 244-259
|
artikel
|
| 5 |
Development of analytical models for tip, root, and end relieving of spur gears by pulsed electrochemical finishing process
|
Rana, Vivek
|
|
|
47 |
C |
p. 132-157
|
artikel
|
| 6 |
Editorial Board
|
|
|
|
47 |
C |
p. ii
|
artikel
|
| 7 |
Evaluation of response characteristics using sensitivity analysis and TLBO technique of powder mixed wire EDM of Ti6Al4V alloy
|
Chakraborty, Sadananda
|
|
|
47 |
C |
p. 260-272
|
artikel
|
| 8 |
Fabrication of YAG ceramics surface without damage and grain boundary steps using catalyzed chemical wet etching
|
Toh, Daisetsu
|
|
|
47 |
C |
p. 1-6
|
artikel
|
| 9 |
Fundamental investigation on process damping potentials of cutting tools with flank face chamfers
|
Wöste, Florian
|
|
|
47 |
C |
p. 7-17
|
artikel
|
| 10 |
Influence of build direction and heat treatment on the microstructure and tensile characteristics of cold metal transfer based wire arc additive manufactured SS 304L
|
O S, Sandeep
|
|
|
47 |
C |
p. 59-70
|
artikel
|
| 11 |
Machine learning approach for weld configuration classification within the GTAW process
|
Boutin, Theo
|
|
|
47 |
C |
p. 116-131
|
artikel
|
| 12 |
Machine learning for rapid inference of critical dimensions in optical metrology of nanopatterned surfaces
|
Sabbagh, Ramin
|
|
|
47 |
C |
p. 184-192
|
artikel
|
| 13 |
Microstructural evolution and mechanical property of friction stir welded joints in AlSi10Mg alloys fabricated by laser powder bed fusion
|
Cui, Li
|
|
|
47 |
C |
p. 228-243
|
artikel
|
| 14 |
MOGA and TOPSIS-based multi-objective optimization of wire EDM process parameters for Ni50.3-Ti29.7-Hf20 alloy
|
V, Balaji
|
|
|
47 |
C |
p. 158-167
|
artikel
|
| 15 |
Multi-objective optimization of mixed-model assembly lines incorporating musculoskeletal risks assessment using digital human modeling
|
Nourmohammadi, Amir
|
|
|
47 |
C |
p. 71-85
|
artikel
|
| 16 |
Multisensor data fusion and machine learning to classify wood products and predict workpiece characteristics during milling
|
Derbas, Mehieddine
|
|
|
47 |
C |
p. 103-115
|
artikel
|
| 17 |
Optimizing joint structure and performance in friction spot joining of aluminum alloy AA6061 and poly-ether-ether-ketone (PEEK)
|
Gao, Yunfeng
|
|
|
47 |
C |
p. 273-282
|
artikel
|
| 18 |
Two different experimental approaches for the uncertainty determination of X-ray computed tomography dimensional measurements on lattice structures
|
Zanini, Filippo
|
|
|
47 |
C |
p. 205-214
|
artikel
|
| 19 |
Vision on metal additive manufacturing: Developments, challenges and future trends
|
Bernard, Alain
|
|
|
47 |
C |
p. 18-58
|
artikel
|
| 20 |
Workpiece temperature investigation in micromilling of titanium alloy
|
dos Santos, Aline Gonçalves
|
|
|
47 |
C |
p. 193-204
|
artikel
|
Tijdschrift beschrijving