| nr |
titel |
auteur |
tijdschrift |
jaar |
jaarg. |
afl. |
pagina('s) |
type |
| 1 |
A comparison of particulate emission for rapeseed oil methyl ester, palm oil methyl ester and soybean oil methyl ester in perspective of their fatty ester composition
|
Zhu, Lei
|
|
2016
|
94 |
C |
p. 249-255
7 p.
|
artikel
|
| 2 |
A knowledge-based system for low-grade waste heat recovery in the process industries
|
Law, Richard
|
|
2016
|
94 |
C |
p. 590-599
10 p.
|
artikel
|
| 3 |
Algorithm and simulation of heat conduction process for design of a thin multilayer technical device
|
Ayriyan, Alexander
|
|
2016
|
94 |
C |
p. 151-158
8 p.
|
artikel
|
| 4 |
A Monte Carlo simulation and effective thermal conductivity calculation for unidirectional fiber reinforced CMC
|
Yan, Dongfang
|
|
2016
|
94 |
C |
p. 827-835
9 p.
|
artikel
|
| 5 |
An experimental study on defrosting performance of an air source heat pump unit with a multi-circuit outdoor coil at different frosting evenness values
|
Song, Mengjie
|
|
2016
|
94 |
C |
p. 331-340
10 p.
|
artikel
|
| 6 |
Annual energy and environment analysis of solarized steam injection gas turbine (STIG) cycle for Indian regions
|
Selwynraj, A. Immanuel
|
|
2016
|
94 |
C |
p. 679-696
18 p.
|
artikel
|
| 7 |
A novel flash boosted evaporation process for alumina refineries
|
Rahimi, Bijan
|
|
2016
|
94 |
C |
p. 375-384
10 p.
|
artikel
|
| 8 |
A passive thermal control method by radiative shield with multi-parameter adjustment capacity
|
Sun, C.
|
|
2016
|
94 |
C |
p. 600-606
7 p.
|
artikel
|
| 9 |
Application of an efficient exponential wide band model for the natural gas combustion simulation in a 300 kW BERL burner furnace
|
Yan, Linbo
|
|
2016
|
94 |
C |
p. 209-220
12 p.
|
artikel
|
| 10 |
A simplified methodology to simulate a heat exchanger in an aircraft's oil cooler by means of a Porous Media model
|
Musto, Marilena
|
|
2016
|
94 |
C |
p. 836-845
10 p.
|
artikel
|
| 11 |
A study on the energy efficiency of specific cutting energy in laser-assisted machining
|
Ahn, Jong Wook
|
|
2016
|
94 |
C |
p. 748-753
6 p.
|
artikel
|
| 12 |
A three-dimensional CFD simulation study to reduce heat stress in ships
|
Pérez, José Antonio
|
|
2016
|
94 |
C |
p. 413-421
9 p.
|
artikel
|
| 13 |
Case study of fault detection and diagnosis of a household air conditioner with a dynamic refrigeration cycle simulator
|
Seo, Jung Ah
|
|
2016
|
94 |
C |
p. 198-208
11 p.
|
artikel
|
| 14 |
CFD modelling of radiators in buildings with user-defined wall functions
|
Risberg, Daniel
|
|
2016
|
94 |
C |
p. 266-273
8 p.
|
artikel
|
| 15 |
Combined convective heat and airborne pollutant removals in a slot vented enclosure under different flow schemes: Parametric investigations and non unique flow solutions
|
Ren, Xiu-Hong
|
|
2016
|
94 |
C |
p. 159-169
11 p.
|
artikel
|
| 16 |
Combustion performance and sodium absorption of ZhunDong coal in a CLC process with hematite oxygen carrier
|
Ge, Huijun
|
|
2016
|
94 |
C |
p. 40-49
10 p.
|
artikel
|
| 17 |
Comparative study on AL2O3 nanoparticle addition on cool storage system performance
|
Attia, Ahmed A.A.
|
|
2016
|
94 |
C |
p. 449-457
9 p.
|
artikel
|
| 18 |
Comparison of different cooling methods for lithium ion battery cells
|
Chen, Dafen
|
|
2016
|
94 |
C |
p. 846-854
9 p.
|
artikel
|
| 19 |
Computational thermal analysis of cylindrical fin design parameters and a new methodology for defining fin structure in LED automobile headlamp cooling applications
|
Sökmen, Kemal Furkan
|
|
2016
|
94 |
C |
p. 534-542
9 p.
|
artikel
|
| 20 |
Corrosion evaluation and prevention of reactor materials to contain thermochemical material for thermal energy storage
|
Solé, Aran
|
|
2016
|
94 |
C |
p. 355-363
9 p.
|
artikel
|
| 21 |
Critical heat balance error for heat exchanger experiment based on entropy generation method
|
Zhang, Zhifeng
|
|
2016
|
94 |
C |
p. 644-649
6 p.
|
artikel
|
| 22 |
3D CFD simulations of acetone hydrogenation in randomly packed beds for an isopropanol–acetone–hydrogen chemical heat pump
|
Peng, Wenping
|
|
2016
|
94 |
C |
p. 238-248
11 p.
|
artikel
|
| 23 |
Design of heat exchangers using a novel multiobjective free search differential evolution paradigm
|
Hultmann Ayala, Helon Vicente
|
|
2016
|
94 |
C |
p. 170-177
8 p.
|
artikel
|
| 24 |
Development and tests of loop heat pipe with multi-layer metal foams as wick structure
|
Zhou, Wei
|
|
2016
|
94 |
C |
p. 324-330
7 p.
|
artikel
|
| 25 |
Development of thermal storage material using vermiculite and calcium hydroxide
|
Kariya, Jun
|
|
2016
|
94 |
C |
p. 186-192
7 p.
|
artikel
|
| 26 |
Editorial board
|
|
|
2016
|
94 |
C |
p. CO2-
1 p.
|
artikel
|
| 27 |
Effects of non-Newtonian behaviour on the thermal performance of nanofluids in a horizontal channel with discrete regions of heating and cooling
|
Li, Botong
|
|
2016
|
94 |
C |
p. 404-412
9 p.
|
artikel
|
| 28 |
Energy efficiency in fishing: Are magnetic devices useful for use in fishing vessels?
|
Gabiña, Gorka
|
|
2016
|
94 |
C |
p. 670-678
9 p.
|
artikel
|
| 29 |
Enhanced combustion efficiency and reduced pollutant emission in a fluidized bed combustor by using porous alumina bed materials
|
Qin, Linbo
|
|
2016
|
94 |
C |
p. 813-818
6 p.
|
artikel
|
| 30 |
Evaluation of different vapor recompression distillation configurations based on energy requirements and associated costs
|
Kazemi, Abolghasem
|
|
2016
|
94 |
C |
p. 305-313
9 p.
|
artikel
|
| 31 |
Experimental and numerical investigation of the thermal performance of a novel sintered-wick heat pipe
|
Khalili, M.
|
|
2016
|
94 |
C |
p. 59-75
17 p.
|
artikel
|
| 32 |
Experimental study on Organic Rankine cycle for low grade thermal energy recovery
|
Pu, Wenhao
|
|
2016
|
94 |
C |
p. 221-227
7 p.
|
artikel
|
| 33 |
Experimental study on the interaction between fire and water mist in long and narrow spaces
|
Zhang, Peihong
|
|
2016
|
94 |
C |
p. 706-714
9 p.
|
artikel
|
| 34 |
Experimental study on the operating characteristics of a novel photovoltaic/thermal integrated dual-source heat pump water heating system
|
Qu, Minglu
|
|
2016
|
94 |
C |
p. 819-826
8 p.
|
artikel
|
| 35 |
Experimentation and cycle performance prediction of hybrid A/C system using automobile exhaust waste heat
|
Wang, Lei
|
|
2016
|
94 |
C |
p. 314-323
10 p.
|
artikel
|
| 36 |
Feasible heat recovery of interplant heat integration between two plants via an intermediate medium analyzed by Interplant Shifted Composite Curves
|
Song, Runrun
|
|
2016
|
94 |
C |
p. 90-98
9 p.
|
artikel
|
| 37 |
Flight deck heat spreader
|
Semenic, Tadej
|
|
2016
|
94 |
C |
p. 1-12
12 p.
|
artikel
|
| 38 |
Flow apportionment algorithm for optimization of power plant ducting
|
Avvari, Ramesh
|
|
2016
|
94 |
C |
p. 715-726
12 p.
|
artikel
|
| 39 |
Flow structure and heat transfer of non-Newtonian fluids in microchannel heat sinks with dimples and protrusions
|
Li, Ping
|
|
2016
|
94 |
C |
p. 50-58
9 p.
|
artikel
|
| 40 |
Full surface heat transfer characteristics of rotor ventilation duct of a turbine generator
|
Yoo, Wonkyung
|
|
2016
|
94 |
C |
p. 385-394
10 p.
|
artikel
|
| 41 |
Heat exchanger network retrofit throughout overall heat transfer coefficient by using genetic algorithm
|
Biyanto, Totok Ruki
|
|
2016
|
94 |
C |
p. 274-281
8 p.
|
artikel
|
| 42 |
Heat transfer enhancement of an impinging synthetic air jet using diffusion-shaped orifice
|
Liu, Yao-Hsien
|
|
2016
|
94 |
C |
p. 178-185
8 p.
|
artikel
|
| 43 |
Improving exergetic performance parameters of a rotating-tray air dryer via a simple heat exchanger
|
Ghasemkhani, Hamid
|
|
2016
|
94 |
C |
p. 13-23
11 p.
|
artikel
|
| 44 |
Improving thermal efficiency and increasing production rate in the double moving beds thermally coupled reactors by using differential evolution (DE) technique
|
Karimi, Mohsen
|
|
2016
|
94 |
C |
p. 543-558
16 p.
|
artikel
|
| 45 |
Influence of air and EGR dilutions on improving performance of a high compression ratio spark-ignition engine fueled with methanol at light load
|
Xie, Fangxi
|
|
2016
|
94 |
C |
p. 559-567
9 p.
|
artikel
|
| 46 |
Influence of sintering parameters of different sintering layers on NOx emission in iron ore sintering process
|
Zhou, Hao
|
|
2016
|
94 |
C |
p. 786-798
13 p.
|
artikel
|
| 47 |
Influence of void ratio on thermal stress of PCM canister for heat pipe receiver
|
Xiaohong, Gui
|
|
2016
|
94 |
C |
p. 615-621
7 p.
|
artikel
|
| 48 |
Infrared thermography measurement of two-phase boiling flow heat transfer in a microchannel
|
Liu, Tsung-Lin
|
|
2016
|
94 |
C |
p. 568-578
11 p.
|
artikel
|
| 49 |
Issues in performance measurement of CO2 compressor near the critical point
|
Lee, Jekyoung
|
|
2016
|
94 |
C |
p. 111-121
11 p.
|
artikel
|
| 50 |
Laser scanning heating method for high-temperature spectral emissivity analyses
|
Honner, Milan
|
|
2016
|
94 |
C |
p. 76-81
6 p.
|
artikel
|
| 51 |
Manufacturing cost model for heat exchangers optimization
|
Caputo, Antonio C.
|
|
2016
|
94 |
C |
p. 513-533
21 p.
|
artikel
|
| 52 |
MIM, FEM and experimental investigations of the thermal drift in an ultra-high precision set-up for dimensional metrology at the nanometre accuracy level
|
Bouderbala, Kamélia
|
|
2016
|
94 |
C |
p. 491-504
14 p.
|
artikel
|
| 53 |
Modeling and optimization of distributed energy supply network with power and hot water interchanges
|
Wu, Qiong
|
|
2016
|
94 |
C |
p. 635-643
9 p.
|
artikel
|
| 54 |
Modeling the self-assembly of nanoparticles into branched aggregates from a sessile nanofluid droplet
|
Zhang, H.
|
|
2016
|
94 |
C |
p. 650-656
7 p.
|
artikel
|
| 55 |
New procedure for design and exergoeconomic optimization of site utility system considering reliability
|
Rad, M. Pouyan
|
|
2016
|
94 |
C |
p. 478-490
13 p.
|
artikel
|
| 56 |
NLP model and stochastic multi-start optimization approach for heat exchanger networks
|
Núñez-Serna, Rosa I.
|
|
2016
|
94 |
C |
p. 458-471
14 p.
|
artikel
|
| 57 |
Nucleate boiling of pure and quasi-azeotropic refrigerants from copper coated surfaces
|
Dewangan, Ashok K.
|
|
2016
|
94 |
C |
p. 395-403
9 p.
|
artikel
|
| 58 |
Numerical analysis of solar enhanced natural draft dry cooling tower configuration
|
Zou, Zheng
|
|
2016
|
94 |
C |
p. 697-705
9 p.
|
artikel
|
| 59 |
Numerical and experimental investigations of electronic evaporative cooling performance with a coiled channel
|
Yin, Xiang
|
|
2016
|
94 |
C |
p. 256-265
10 p.
|
artikel
|
| 60 |
Numerical investigations on two-phase flow modes in evaporative condensers
|
Fiorentino, Maria
|
|
2016
|
94 |
C |
p. 777-785
9 p.
|
artikel
|
| 61 |
Numerical study of pulverized coal-fired utility boiler over a wide range of operating conditions for in-furnace SO2/NOx reduction
|
Belošević, Srdjan
|
|
2016
|
94 |
C |
p. 657-669
13 p.
|
artikel
|
| 62 |
On-line monitoring and control of thermal stresses in steam turbine rotors
|
Banaszkiewicz, Mariusz
|
|
2016
|
94 |
C |
p. 763-776
14 p.
|
artikel
|
| 63 |
On predicting the length, width, and volume of the jet diffusion flame
|
Kang, Yinhu
|
|
2016
|
94 |
C |
p. 799-812
14 p.
|
artikel
|
| 64 |
Optimization of mixed working fluids for a novel trigeneration system based on organic Rankine cycle installed with heat pumps
|
Li, Zishen
|
|
2016
|
94 |
C |
p. 754-762
9 p.
|
artikel
|
| 65 |
Performance comparison of the liquid–vapor separation, parallel flow, and serpentine condensers in the organic Rankine cycle
|
Luo, Xianglong
|
|
2016
|
94 |
C |
p. 435-448
14 p.
|
artikel
|
| 66 |
Performance improvement of the finned passive PVT system using reflectors like removable insulation covers
|
Ziapour, Behrooz M.
|
|
2016
|
94 |
C |
p. 341-349
9 p.
|
artikel
|
| 67 |
Performance of an absorption heat transformer using new working binary systems composed of {ionic liquid and water}
|
Abumandour, El-Shaimaa
|
|
2016
|
94 |
C |
p. 579-589
11 p.
|
artikel
|
| 68 |
Performance optimization of adiabatic compressed air energy storage with ejector technology
|
Guo, Zuogang
|
|
2016
|
94 |
C |
p. 193-197
5 p.
|
artikel
|
| 69 |
Prediction of heat transfer during condensation in inclined plain tubes
|
Shah, Mirza M.
|
|
2016
|
94 |
C |
p. 82-89
8 p.
|
artikel
|
| 70 |
Reduced material model for closed cell metal foam infiltrated with phase change material based on high resolution numerical studies
|
Ohsenbrügge, Christoph
|
|
2016
|
94 |
C |
p. 505-512
8 p.
|
artikel
|
| 71 |
Research on a feature selection method based on median impact value for modeling in thermal power plants
|
Qi, Minfang
|
|
2016
|
94 |
C |
p. 472-477
6 p.
|
artikel
|
| 72 |
Selection of optimal mixed liquid desiccants and performance analysis of the liquid desiccant cooling system
|
Zhao, Xiao
|
|
2016
|
94 |
C |
p. 622-634
13 p.
|
artikel
|
| 73 |
Silicon carbide nanowires suspensions with high thermal transport properties
|
Yu, Wei
|
|
2016
|
94 |
C |
p. 350-354
5 p.
|
artikel
|
| 74 |
Study on energy and economic benefits of converting a combined heating and power system to a tri-generation system for sewage treatment plants in subtropical area
|
Chen, Yi
|
|
2016
|
94 |
C |
p. 24-39
16 p.
|
artikel
|
| 75 |
Study on the critical velocity in a sloping tunnel fire under longitudinal ventilation
|
Weng, Miao-cheng
|
|
2016
|
94 |
C |
p. 422-434
13 p.
|
artikel
|
| 76 |
Support vector machine-based exergetic modelling of a DI diesel engine running on biodiesel–diesel blends containing expanded polystyrene
|
Shamshirband, Shahaboddin
|
|
2016
|
94 |
C |
p. 727-747
21 p.
|
artikel
|
| 77 |
The effects of element direction and intersection angle of adjacent Q-type inserts on the laminar flow and heat transfer
|
Yu, Yanfang
|
|
2016
|
94 |
C |
p. 282-295
14 p.
|
artikel
|
| 78 |
The influence of low air pressure on horizontal flame spread over flexible polyurethane foam and correlative smoke productions
|
Tu, Ran
|
|
2016
|
94 |
C |
p. 133-140
8 p.
|
artikel
|
| 79 |
Thermal and electrical performances of a water-surface floating PV integrated with double water-saturated MEPCM layers
|
Ho, C.J.
|
|
2016
|
94 |
C |
p. 122-132
11 p.
|
artikel
|
| 80 |
Thermally induced stresses on radiant heating tubes including the effect of fluid–structure interaction
|
Hellenkamp, Martin
|
|
2016
|
94 |
C |
p. 364-374
11 p.
|
artikel
|
| 81 |
Thermal radiation analysis for small satellites with single-node model using techniques of equivalent linearization
|
Anh, N.D.
|
|
2016
|
94 |
C |
p. 607-614
8 p.
|
artikel
|
| 82 |
Towards the increased utilisation of geothermal energy in a district heating network through the use of a heat storage
|
Kyriakis, Sotirios A.
|
|
2016
|
94 |
C |
p. 99-110
12 p.
|
artikel
|
| 83 |
Two-stage double-effect ammonia/lithium nitrate absorption cycle
|
Ventas, R.
|
|
2016
|
94 |
C |
p. 228-237
10 p.
|
artikel
|
| 84 |
Using data centres for combined heating and cooling: An investigation for London
|
Davies, G.F.
|
|
2016
|
94 |
C |
p. 296-304
9 p.
|
artikel
|
| 85 |
Waste fish oil (WFO) esterification catalyzed by sulfonated activated carbon under ultrasound irradiation
|
Hajamini, Zahra
|
|
2016
|
94 |
C |
p. 141-150
10 p.
|
artikel
|
Tijdschrift beschrijving