no |
title |
author |
magazine |
year |
volume |
issue |
page(s) |
type |
1 |
A combined first-principles calculation and thermodynamic modeling of the F–K–Na system
|
Zhang, Shengjun |
|
2006 |
418 |
1-2 |
p. 161-171 11 p. |
article |
2 |
AFM and EBSD combined studies of plastic deformation in a duplex stainless steel
|
Fréchard, S. |
|
2006 |
418 |
1-2 |
p. 312-319 8 p. |
article |
3 |
Annealing behavior of coarse-grained titanium deformed by cold rolling
|
Hayama, A.O.F. |
|
2006 |
418 |
1-2 |
p. 182-192 11 p. |
article |
4 |
A review of wet impregnation—An alternative method for the fabrication of high performance and nano-structured electrodes of solid oxide fuel cells
|
Jiang, San Ping |
|
2006 |
418 |
1-2 |
p. 199-210 12 p. |
article |
5 |
A simple test to determine the effectiveness of different braze compositions for joining Ti-tubes to C/C composite plates
|
Morscher, Gregory N. |
|
2006 |
418 |
1-2 |
p. 19-24 6 p. |
article |
6 |
A study of the stress and resistivity of Al/Ti films deposited by an ion beam assisted process for surface acoustic wave devices applications
|
Li, D.M. |
|
2006 |
418 |
1-2 |
p. 218-222 5 p. |
article |
7 |
Austenite reformation in the heat-affected zone of duplex stainless steel 2205
|
Sieurin, Henrik |
|
2006 |
418 |
1-2 |
p. 250-256 7 p. |
article |
8 |
Author Index
|
|
|
2006 |
418 |
1-2 |
p. 370-371 2 p. |
article |
9 |
Compression creep of PM aluminum matrix composites reinforced with SiC short fibres
|
Moreno, Mario F. |
|
2006 |
418 |
1-2 |
p. 172-181 10 p. |
article |
10 |
Cyclic plasticity of soft oriented NiAl single crystals at 600K
|
Holste, C. |
|
2006 |
418 |
1-2 |
p. 1-10 10 p. |
article |
11 |
Design of powder metallurgy titanium alloys and composites
|
Liu, Y. |
|
2006 |
418 |
1-2 |
p. 25-35 11 p. |
article |
12 |
Effect of root flaws on the fatigue property of friction stir welds in 2024-T3 aluminum alloys
|
Zhou, Caizhi |
|
2006 |
418 |
1-2 |
p. 155-160 6 p. |
article |
13 |
Effects of h-BN additive on the microstructure and mechanical properties of AlN-based machinable ceramics
|
Cho, Won-Seung |
|
2006 |
418 |
1-2 |
p. 61-67 7 p. |
article |
14 |
Evolution of misorientation distribution during warm ‘abc’ forging of commercial-purity titanium
|
Mironov, S.Yu. |
|
2006 |
418 |
1-2 |
p. 257-267 11 p. |
article |
15 |
Fatigue behaviour of cast irons with spheroidal vanadium carbides dispersed within martensitic matrix microstructure
|
Tokaji, K. |
|
2006 |
418 |
1-2 |
p. 326-334 9 p. |
article |
16 |
Fatigue damage and fracture behavior of tungsten fiber reinforced Zr-based metallic glassy composite
|
Zhang, H. |
|
2006 |
418 |
1-2 |
p. 146-154 9 p. |
article |
17 |
High-purity amorphous Zr52.5Cu17.9Ni14.6Al10Ti5 powders via mechanical amorphization of crystalline pre-alloys
|
Siegrist, Marco E. |
|
2006 |
418 |
1-2 |
p. 236-240 5 p. |
article |
18 |
Influence of modified processing on structure and properties of hot isostatically pressed superalloy Inconel 718
|
Rao, G. Appa |
|
2006 |
418 |
1-2 |
p. 282-291 10 p. |
article |
19 |
Influence of pre-compression on microstructure and creep characteristic of a single crystal nickel-base superalloy
|
Shui, Li |
|
2006 |
418 |
1-2 |
p. 229-235 7 p. |
article |
20 |
Influences of Mo substitution by W on the precipitation kinetics of secondary phases and the associated localized corrosion and embrittlement in 29% Cr ferritic stainless steels
|
Park, Chan-Jin |
|
2006 |
418 |
1-2 |
p. 211-217 7 p. |
article |
21 |
Inside Front Cover: Editorial Board
|
|
|
2006 |
418 |
1-2 |
p. CO2- 1 p. |
article |
22 |
Macroscale constitutive modeling of kinking nonlinear elastic solids
|
Kalidindi, S.R. |
|
2006 |
418 |
1-2 |
p. 95-98 4 p. |
article |
23 |
Mechanical property of induction brazing TiAl-based intermetallics to steel 35CrMo using AgCuTi filler metal
|
He, P. |
|
2006 |
418 |
1-2 |
p. 45-52 8 p. |
article |
24 |
Microstructural effects of AZ31 magnesium alloy on its tensile deformation and failure behaviors
|
Marya, Manuel |
|
2006 |
418 |
1-2 |
p. 341-356 16 p. |
article |
25 |
Microstructure and kinetics of induction brazing TiAl-based intermetallics to steel 35CrMo using AgCuTi filler metal
|
He, P. |
|
2006 |
418 |
1-2 |
p. 53-60 8 p. |
article |
26 |
Microstructure of surface composite Al2O3/Ni on copper substrate produced by vacuum infiltration casting
|
Yang, Gui-rong |
|
2006 |
418 |
1-2 |
p. 223-228 6 p. |
article |
27 |
Multi-layer functionally graded Mg2Si/Al composite produced by directional remelting and quenching process
|
Qin, Q.D. |
|
2006 |
418 |
1-2 |
p. 193-198 6 p. |
article |
28 |
Near surface deformation associated with the scratch in polypropylene–clay nanocomposite: A microscopic study
|
Thridandapani, R.R. |
|
2006 |
418 |
1-2 |
p. 292-302 11 p. |
article |
29 |
Numerical simulation of nonlinear elastic wave propagation in piecewise homogeneous media
|
Berezovski, Arkadi |
|
2006 |
418 |
1-2 |
p. 364-369 6 p. |
article |
30 |
Numerical treatment of the galvannealing process
|
Verma, A.K. |
|
2006 |
418 |
1-2 |
p. 335-340 6 p. |
article |
31 |
On stress whitening during surface deformation in clay-containing polymer nanocomposites: A microstructural approach
|
Hadal, R. |
|
2006 |
418 |
1-2 |
p. 268-281 14 p. |
article |
32 |
Plasticity at a Cu/α-Al2O3 interface with nanovoids
|
Dmitriev, Sergey V. |
|
2006 |
418 |
1-2 |
p. 36-44 9 p. |
article |
33 |
Recombinant domain movement mechanism in superplastic deformation of TZP ceramics
|
Yasuda, Kouichi |
|
2006 |
418 |
1-2 |
p. 115-119 5 p. |
article |
34 |
Relations between microstructure, precipitation, age-formability and damage tolerance of Al–Cu–Mg–Li (Mn, Zr, Sc) alloys for age forming
|
Starink, M.J. |
|
2006 |
418 |
1-2 |
p. 241-249 9 p. |
article |
35 |
Research on the structures and discharge capacities of Mg–Ni alloy with different Ni contents synthesized by high-energy ball milling
|
Shengqi, Xi |
|
2006 |
418 |
1-2 |
p. 81-85 5 p. |
article |
36 |
Subject Index
|
|
|
2006 |
418 |
1-2 |
p. 372-377 6 p. |
article |
37 |
Synthesis and evaluation of hardness and sliding wear resistance of electrodeposited nanocrystalline Ni–W alloys
|
Sriraman, K.R. |
|
2006 |
418 |
1-2 |
p. 303-311 9 p. |
article |
38 |
The characteristics of Cu–12wt.% Ag filamentary microcomposite in different isothermal process
|
Liu, J.B. |
|
2006 |
418 |
1-2 |
p. 320-325 6 p. |
article |
39 |
The hot working characteristics of a boron bearing and a conventional low carbon steel
|
Stumpf, Waldo |
|
2006 |
418 |
1-2 |
p. 86-94 9 p. |
article |
40 |
The mechanical properties and fracture mechanisms of wrought low carbon arc cast (LCAC), molybdenum–0.5pct titanium–0.1pct zirconium (TZM), and oxide dispersion strengthened (ODS) molybdenum flat products
|
Cockeram, B.V. |
|
2006 |
418 |
1-2 |
p. 120-136 17 p. |
article |
41 |
The microstructural characteristics of the deformed nanocrystalline cobalt
|
Zhang, Xiyan |
|
2006 |
418 |
1-2 |
p. 77-80 4 p. |
article |
42 |
Thermal shock resistance of functionally gradient solid cylinders
|
Zhao, Jun |
|
2006 |
418 |
1-2 |
p. 99-110 12 p. |
article |
43 |
Tribological behavior of TiCN-based cermets at elevated temperatures
|
Meng, Junhu |
|
2006 |
418 |
1-2 |
p. 68-76 9 p. |
article |
44 |
Tribological wear behavior of diamond reinforced composite coating
|
Venkateswarlu, K. |
|
2006 |
418 |
1-2 |
p. 357-363 7 p. |
article |
45 |
Two- and three-dimensional microstructural characterization of a super-austenitic stainless steel
|
Lewis, A.C. |
|
2006 |
418 |
1-2 |
p. 11-18 8 p. |
article |
46 |
Wear resistance of WC particle reinforced copper matrix composites and the effect of porosity
|
Deshpande, P.K. |
|
2006 |
418 |
1-2 |
p. 137-145 9 p. |
article |
47 |
X-ray and EPR study of reactions between B4C and TiO2
|
Kakazey, M. |
|
2006 |
418 |
1-2 |
p. 111-114 4 p. |
article |