Digitale Bibliotheek
Sluiten Bladeren door artikelen uit een tijdschrift
 
Zoeken naar met titel:
ABCDEFGHIJKLMNOPQRSTUVWXYZ

     Tijdschrift beschrijving
       Alle jaargangen van het bijbehorende tijdschrift
         Alle afleveringen van het bijbehorende jaargang
                                       Alle artikelen van de bijbehorende aflevering
 
                             37 gevonden resultaten
nr titel auteur tijdschrift jaar jaarg. afl. pagina('s) type
1 A cost-effective P/M titanium matrix composite for automobile use 1996
 18 5 p. 343-
1 p.
 artikel
2 Aerospace materials 1996
 18 5 p. 343-
1 p.
 artikel
3 An integrated approach to life assessment 1996
 18 5 p. 343-
1 p.
 artikel
4 Application of Monte Carlo simulation for fractographic analysis of fatigue crack propagation Shimokawa, T.
 1996
 18 5 p. 321-327
7 p.
 artikel
5 A two-dimensional micromechanic fatigue model 1996
 18 5 p. 345-
1 p.
 artikel
6 Calendar 1996
 18 5 p. 347-348
2 p.
 artikel
7 Creep fatigue. I. Compilation of data and trends in the creep-fatigue behavior of low alloy steels 1996
 18 5 p. 345-
1 p.
 artikel
8 Creep fatigue. II. Creep fatigue life prediction: methods and trends 1996
 18 5 p. 345-
1 p.
 artikel
9 Creep fatigue. III. Diercks equation: modification and applicability 1996
 18 5 p. 345-
1 p.
 artikel
10 Cyclic axial-torsional deformation behaivor of a cobalt-base superalloy 1996
 18 5 p. 344-
1 p.
 artikel
11 Dislocation structure of fatigue crack tip 1996
 18 5 p. 345-
1 p.
 artikel
12 Effect of mean stress and ratcheting strain on fatigue life of steel Xia, Z.
 1996
 18 5 p. 335-341
7 p.
 artikel
13 Effect of microstructure on fatigue crack growth of Ti3AlNb alloys 1996
 18 5 p. 344-345
2 p.
 artikel
14 Effect of surface finish on fatigue strength 1996
 18 5 p. 344-
1 p.
 artikel
15 Evaluation of 6013-T6 sheet for damage tolerance applications 1996
 18 5 p. 345-
1 p.
 artikel
16 Evolution of grain boundary serration in fatigue 1996
 18 5 p. 345-346
2 p.
 artikel
17 Fatigue crack initatiin in high-purity titanium crystals Tan Xiaoli,
 1996
 18 5 p. 329-333
5 p.
 artikel
18 Fatigue strength of high-strength fine-grained structural steels in the flame cut condition 1996
 18 5 p. 345-
1 p.
 artikel
19 Improved cast steel back-up rolls for hot and cold rolling mills 1996
 18 5 p. 344-
1 p.
 artikel
20 Influence of applied load on rolling contact fatigue of CMn induction-hardened bearing steel 1996
 18 5 p. 344-
1 p.
 artikel
21 Influence of material and mechanical properties on thermal fatigue life of aluminum castings 1996
 18 5 p. 345-
1 p.
 artikel
22 Influence of microstructure on the fatigue properties of austempered ductile irons—I. High-cycle fatigue Lin, C.-K.
 1996
 18 5 p. 297-307
11 p.
 artikel
23 Influence of microstructure on the fatigue properties of austempered ductile irons—II. Low-cycle fatigue Lin, C.-K.
 1996
 18 5 p. 309-320
12 p.
 artikel
24 Influence of retained austenite in high chromium cast iron on impact fatigue wear 1996
 18 5 p. 346-
1 p.
 artikel
25 Initiation and growth of small fatigue cracks in a nickel-base superalloy 1996
 18 5 p. 344-
1 p.
 artikel
26 Intrinsic statistical characteristics of fatigue crack growth rate 1996
 18 5 p. 344-
1 p.
 artikel
27 Investigation of failures in stainless steel orthopaedic implant devices: pit-induced fatigue cracks 1996
 18 5 p. 343-
1 p.
 artikel
28 Long-life variable amplitude fatigue behavior of steel bridges 1996
 18 5 p. 344-
1 p.
 artikel
29 Mode I fatigue crack growth in a continuous alumina fibre-reinforced magnesium matrix composite Nayeb-Hashemi, H
 1996
 18 5 p. 287-296
10 p.
 artikel
30 NDT of aircraft structures during full-scale fatigue testing 1996
 18 5 p. 346-
1 p.
 artikel
31 Optimization of the material properties of titanium turbine blades used in steam turbines (Optimierung der Werkstoffeigenschaften von Titan-Turbinenschaufein fur den Einsatz in Dampfturbinen) 1996
 18 5 p. 345-
1 p.
 artikel
32 SIMS microprofiles of Pb5%Sn solder joints in electronic devices after accelerated life tests 1996
 18 5 p. 346-
1 p.
 artikel
33 Some aspects of fatigue thresholds under mode III and mixed mode III and I loadings Tong, J.
 1996
 18 5 p. 279-285
7 p.
 artikel
34 Surface modification 1996
 18 5 p. 343-
1 p.
 artikel
35 Testing materials under multi-axial loading 1996
 18 5 p. 346-
1 p.
 artikel
36 The double slip plane model for the study of short cracks 1996
 18 5 p. 345-
1 p.
 artikel
37 Use of aluminum in automotive space frames 1996
 18 5 p. 343-
1 p.
 artikel
                             37 gevonden resultaten
 
 Koninklijke Bibliotheek - Nationale Bibliotheek van Nederland