nr |
titel |
auteur |
tijdschrift |
jaar |
jaarg. |
afl. |
pagina('s) |
type |
1 |
Carrying Gas Influence and Fabrication Parameters Impact in 3D Manufacturing of In Situ TiN-Ti Composites by Direct Laser Deposition
|
de Rojas Candela, C. Sánchez |
|
|
29 |
3 |
p. 591-606 |
artikel |
2 |
Correction to: Properties Augmentation of Cast Hypereutectic Al–Si Alloy Through Friction Stir Processing
|
Bates, William P. |
|
|
29 |
3 |
p. 876 |
artikel |
3 |
Correction to: Researches on a Novel Severe Plastic Deformation Method Combining Direct Extrusion and Shearings for AZ61 Magnesium Alloy Based on Numerical Simulation and Experiments
|
Hongjun, Hu |
|
|
29 |
3 |
p. 874-875 |
artikel |
4 |
Dealloying Superalloy by Liquid Mg for the Selective Extraction of Ni
|
Cui, Fuhui |
|
|
29 |
3 |
p. 833-844 |
artikel |
5 |
Effect of Cooling Rate on Pitting Corrosion Behavior of 904L Austenitic Stainless Steel in a Simulated Flue Gas Desulfurization Solution
|
Li, Miaomiao |
|
|
29 |
3 |
p. 730-747 |
artikel |
6 |
Effect of Cr Addition on Properties and Tribological Behavior at Elevated Temperature of Boride Layers Grown on Borosintered Powder Metallurgy Alloys
|
Günen, Ali |
|
|
29 |
3 |
p. 748-766 |
artikel |
7 |
Effect of Powder Bed Fusion Process Parameters on Microstructural and Mechanical Properties of FeCrNi MEA: An Atomistic Study
|
Jamil, Ishat Raihan |
|
|
29 |
3 |
p. 659-673 |
artikel |
8 |
Effect of Precipitation Behavior on Mechanical Properties of a Nb-Containing CoCrNi-Based High-Entropy Alloy
|
Zhou, Hongchi |
|
|
29 |
3 |
p. 674-692 |
artikel |
9 |
Effect of Pulse Current GMAW on the Yield Stress of the S460M TMCP Steel Welded Joints
|
Zavdoveev, A. |
|
|
29 |
3 |
p. 795-806 |
artikel |
10 |
Effects of the Alloy Design and Fabrication Process on Mechanical Properties of Mo + V-Added SA508 Gr.1A Steel for Main Steam Line Piping in Nuclear Power Plants
|
Hong, Seokmin |
|
|
29 |
3 |
p. 693-704 |
artikel |
11 |
Experimental Investigation and Crystal Plasticity Simulation with Damage for Single Crystal Copper Subjected to Tensile Load
|
Paik, Suman |
|
|
29 |
3 |
p. 618-633 |
artikel |
12 |
Friction Stir Processing of Cold-Sprayed High-Entropy Alloy Particles Reinforced Aluminum Matrix Composites: Corrosion and Wear Properties
|
Han, Peng |
|
|
29 |
3 |
p. 845-860 |
artikel |
13 |
Inclusion Characteristics and Acicular Ferrite Formation in the Simulated Heat-Affected Zone of Ti-Zr-Killed Low-Carbon Steel
|
Liu, Fangce |
|
|
29 |
3 |
p. 715-729 |
artikel |
14 |
Influence of Annealing on Microstructure and Tribological Properties of AlCoCrFeNiTi High Entropy Alloy Based Coating
|
Kumar, Himanshu |
|
|
29 |
3 |
p. 645-658 |
artikel |
15 |
Intrinsic Heat Treatment of an Additively Manufactured Medium Entropy AlCrFe2Ni2-Alloy
|
Rittinghaus, Silja-Katharina |
|
|
29 |
3 |
p. 579-590 |
artikel |
16 |
Large Compressive Plasticity of Brittle La69Co17Al14 Bulk Metallic Glass Under Constrained Compression
|
Shao, K. W. |
|
|
29 |
3 |
p. 870-873 |
artikel |
17 |
Mechanical Properties and Microstructure Evolution of Pre-stretched Aluminum Alloy After Induced Electro-Pulsing Treatment
|
Wang, Shipeng |
|
|
29 |
3 |
p. 634-644 |
artikel |
18 |
Microstructure Characteristics, Mechanical Properties and Strain Hardening Behavior of Nitrogen-Bearing Fe-0.2 C-5Mn TRIP Steel
|
Zhang, Bao-Guang |
|
|
29 |
3 |
p. 607-617 |
artikel |
19 |
Novel Process for the Formation of Goss Grains by Concentrated Shear Strain on Surface in Inhibitor-Free Silicon Steel
|
Na, Jungkyun |
|
|
29 |
3 |
p. 821-832 |
artikel |
20 |
Prediction of Pressure-Composition-Temperature Curves of AB2-Type Hydrogen Storage Alloys by Machine Learning
|
Kim, Jeong Min |
|
|
29 |
3 |
p. 861-869 |
artikel |
21 |
Quantifying Susceptibility to Solidification Cracking in Oscillated CM247LC Superalloy Welds via Varestraint Testing
|
Kim, Kyeong-Min |
|
|
29 |
3 |
p. 777-794 |
artikel |
22 |
RETRACTED ARTICLE: Experimental and Numerical Investigation of VMR and HPTR Pilgering of Zr–1.5%Nb Tubes
|
Musazadeh, M. H. |
|
|
29 |
3 |
p. 877 |
artikel |
23 |
Role of Ultrasonic Melt Treatment in the Improvement of Corrosion Resistance of Al–7Si–0.4Mg Cast Alloy
|
Kim, Soo-Bae |
|
|
29 |
3 |
p. 705-714 |
artikel |
24 |
Single Track Geometry Prediction of Laser Metal Deposited 316L-Si Via Multi-Physics Modelling and Regression Analysis with Experimental Validation
|
Biyikli, Merve |
|
|
29 |
3 |
p. 807-820 |
artikel |
25 |
Transition Strategy Optimization of Inconel625-HSLA Steel Functionally Graded Material Fabricated by Wire Arc Additive Manufacturing
|
Zhang, Jiarong |
|
|
29 |
3 |
p. 767-776 |
artikel |