| no |
title |
author |
magazine |
year |
volume |
issue |
page(s) |
type |
| 1 |
Analytical investigation of porous pin fins with variable section in fully-wet conditions
|
Vahabzadeh, A.
|
|
2015
|
5 |
C |
p. 1-12
12 p.
|
article
|
| 2 |
A new method for non-Fourier thermal response in a single layer skin tissue
|
Kundu, Balaram
|
|
2015
|
5 |
C |
p. 79-88
10 p.
|
article
|
| 3 |
A numerical study on helical vortices induced by a short twisted tape in a circular pipe
|
Liu, Wen
|
|
2015
|
5 |
C |
p. 134-142
9 p.
|
article
|
| 4 |
A research on thermoelectric generator's electrical performance under temperature mismatch conditions for automotive waste heat recovery system
|
Tang, Z.B.
|
|
2015
|
5 |
C |
p. 143-150
8 p.
|
article
|
| 5 |
A Taguchi approach for optimization of flow and geometrical parameters in a rectangular channel roughened with V down perforated baffles
|
Chamoli, Sunil
|
|
2015
|
5 |
C |
p. 59-69
11 p.
|
article
|
| 6 |
Beneficial design of unbaffled shell-and-tube heat exchangers for attachment of longitudinal fins with trapezoidal profile
|
Kundu, Balaram
|
|
2015
|
5 |
C |
p. 104-112
9 p.
|
article
|
| 7 |
Chemical non-equilibrium flow analysis of H2 fueled scramjet nozzle
|
Huang, Yue
|
|
2015
|
5 |
C |
p. 89-97
9 p.
|
article
|
| 8 |
Corrigendum to “Study of forced convection nanofluid heat transfer in the automotive cooling system” [Case Stud. Therm. Eng. 16 (2014) 50–61]
|
Hussein, Adnan M.
|
|
2015
|
5 |
C |
p. 113-
1 p.
|
article
|
| 9 |
Design and analysis of a cogeneration plant using heat recovery of a cement factory
|
Pradeep Varma, G.V.
|
|
2015
|
5 |
C |
p. 24-31
8 p.
|
article
|
| 10 |
Enhance heat transfer in the channel with V-shaped wavy lower plate using liquid nanofluids
|
Abed, Azher M.
|
|
2015
|
5 |
C |
p. 13-23
11 p.
|
article
|
| 11 |
Enhancement heat transfer characteristics in the channel with Trapezoidal rib–groove using nanofluids
|
Al-Shamani, Ali Najah
|
|
2015
|
5 |
C |
p. 48-58
11 p.
|
article
|
| 12 |
Explicit representation of the implicit Colebrook–White equation
|
Rollmann, P.
|
|
2015
|
5 |
C |
p. 41-47
7 p.
|
article
|
| 13 |
Heat transfer and pressure drop comparison of louver- and plain-finned heat exchangers where one fluid passes through flattened tubes
|
Gorman, J.M.
|
|
2015
|
5 |
C |
p. 122-126
5 p.
|
article
|
| 14 |
Investigations for effect of Al2O3–H2O nanofluid flow rate on the efficiency of direct absorption solar collector
|
Gupta, Hemant Kumar
|
|
2015
|
5 |
C |
p. 70-78
9 p.
|
article
|
| 15 |
Molecular dynamics simulation on flow behaviors of nanofluids confined in nanochannel
|
Cui, Wenzheng
|
|
2015
|
5 |
C |
p. 114-121
8 p.
|
article
|
| 16 |
Performance modeling of industrial gas turbines with inlet air filtration system
|
Effiom, Samuel O.
|
|
2015
|
5 |
C |
p. 160-167
8 p.
|
article
|
| 17 |
Prediction of small spark ignited engine performance using producer gas as fuel
|
Homdoung, N.
|
|
2015
|
5 |
C |
p. 98-103
6 p.
|
article
|
| 18 |
Prototype implementation and experimental analysis of water heating using recovered waste heat of chimneys
|
Khaled, Mahmoud
|
|
2015
|
5 |
C |
p. 127-133
7 p.
|
article
|
| 19 |
Study on effectiveness of continuous solar dryer integrated with desiccant thermal storage for drying cocoa beans
|
Dina, Sari Farah
|
|
2015
|
5 |
C |
p. 32-40
9 p.
|
article
|
| 20 |
Water solar distiller productivity enhancement using concentrating solar water heater and phase change material (PCM)
|
Chaichan, Miqdam T.
|
|
2015
|
5 |
C |
p. 151-159
9 p.
|
article
|
Journal description